mrklaw Posted June 3, 2012 I'm trying to make a slightly larger model of the Big Ben architecture set, to allow me to not have the clock face sticking out. But I've run into trouble with the roof. Seems that Lego don't make any 75 degree corner pieces. This seems odd, as they have a 75 degree slope, and a roof 'cap' but no corners. So any suggestions how to work around this? I was thinking to use the smallest wedge pieces, but I'm having trouble figuring out how to hinge them at an angle to form a roof. I've tried the standard 45 degree slopes and they just look wrong. I need the roof to be four studs wide at the bottom, two studs wide at the top and about a brick high, maybe 4 studs. Plus I need to be able to build on top of it, so I need to be able to get something through from underneath - even if it's just a pole Share this post Link to post Share on other sites
questforcastle Posted June 3, 2012 Try this thread for a start? http://www.eurobricks.com/forum/index.php?showtopic=34961 Share this post Link to post Share on other sites
SNIPE Posted June 4, 2012 (edited) Easy, you get a roof tile which is sloped and turn it sideways. then keep putting them together so it goes higher and narrower like this and put the windows and stuff in sideways if it looks fine or think of some way to have the windows upright and the roof like in the images, it shouldn't be too hard and building on top of this should be easy too with the /modified bricks/technic bricks' as they are called on brick shelf. I have no idea how to picture what roof shape you want or the dimensions, '1 brick high' does not tell me much Edited June 4, 2012 by SNIPE Share this post Link to post Share on other sites
LEGO Historian Posted June 5, 2012 I'm trying to make a slightly larger model of the Big Ben architecture set, to allow me to not have the clock face sticking out. But I've run into trouble with the roof. Seems that Lego don't make any 75 degree corner pieces. This seems odd, as they have a 75 degree slope, and a roof 'cap' but no corners. So any suggestions how to work around this? I was thinking to use the smallest wedge pieces, but I'm having trouble figuring out how to hinge them at an angle to form a roof. I've tried the standard 45 degree slopes and they just look wrong. I need the roof to be four studs wide at the bottom, two studs wide at the top and about a brick high, maybe 4 studs. Plus I need to be able to build on top of it, so I need to be able to get something through from underneath - even if it's just a pole ??? http://www.bricklink.com/catalogItem.asp?P=3685 Share this post Link to post Share on other sites
LEGOman273 Posted June 5, 2012 Use wedge plates attached to hinges. Similer to Hagrid's Hut. Share this post Link to post Share on other sites
Rook Posted June 5, 2012 (edited) SNOT the roof. Build walls and ends of the wall with 3x2x1 tall slopes. Using hinges, tilt the 4 walls towards each other until they touch along their out edged slopes. (Similar to what LEGOman said but using bricks instead of plates.) See here it is done inverted coming down from the control room of the Sand Crawler. This isn’t related to what I said but it’s cool: Edited June 5, 2012 by Rook Share this post Link to post Share on other sites
LEGOman273 Posted June 5, 2012 SNOT the roof. Build walls and ends of the wall with 3x2x1 tall slopes. Using hinges, tilt the 4 walls towards each other until they touch along their out edged slopes. (Similar to what LEGOman said but using bricks instead of plates.) See here it is done inverted coming down from the control room of the Sand Crawler. *Snip* Who built that?! Share this post Link to post Share on other sites
LEGO Historian Posted June 5, 2012 (edited) mrklaw... is this the type of tower roof you are trying to build? This is my 20 year old City Hall model that used yellow 2x2x3 double convex slopes from 7 Yellow Castle (375/6075) sets, back before there was Bricklink! Edited June 5, 2012 by LEGO Historian Share this post Link to post Share on other sites
purpleparadox Posted June 5, 2012 @LEGO Historian: That is an awesome MOC! You've been building great creations since before I was born! Share this post Link to post Share on other sites
mrklaw Posted June 6, 2012 (edited) This is what I have so far. The roof area is only 4x4 studs (area just above the clock face), and needs to leave studs exposed for the top part This kind of works ok, and also the longer 1x2 cheese slopes with slats work in there as well (This one), I just didn't have them in dark bley It's the small working area that is stumping me a little. Edited June 6, 2012 by mrklaw Share this post Link to post Share on other sites
LEGO Historian Posted June 8, 2012 (edited) @LEGO Historian: That is an awesome MOC! You've been building great creations since before I was born! Thanks! (Except for the "before I was born part"..... lol ) Here's a "LEGO Museum of Art" building I did in the early 1990s... sigh... also before you were born.... It is made of white LEGO... which doesn't show well with flash photography, so I omitted the flash, which is why it looks yellowish... (and of course those curve railing pieces in the roof cupola's were a recent addition). Edited June 8, 2012 by LEGO Historian Share this post Link to post Share on other sites
PMJ Posted June 12, 2012 I am referring to this. I need it in a light gray to replace them on this. Share this post Link to post Share on other sites
brickmack Posted June 12, 2012 You might be able to use this, but its about $0.20 each on bricklink, so it could be a bit expensive... Share this post Link to post Share on other sites
TimeCruiser Posted June 13, 2012 You could also try using 61068, 88930, 50950, or 30602 with SNOT building. Share this post Link to post Share on other sites
Faefrost Posted June 13, 2012 This is how someone at a large public show addressed the issue in an Alien Conquest MOC. But I think they may have also been trying to make the profile a little more angular to match some of the AC concept art. (I wish I knew who had made that MOC) The thing that hurts with any alternatives is they will cost you those side pin holes, which means you will not have the opening cockpit doors or side door. Share this post Link to post Share on other sites
Aanchir Posted June 13, 2012 I am referring to this. I need it in a light gray to replace them on this. These would be harder to incorporate than the other suggestions, could require somewhat heavy customization, and might require eliminating the hinge function the original parts allow, but I figure I might throw in that suggestion along with the System solutions others have recommended. Of course, chances are you want to keep the hinge function, so these probably won't work too well for your individual needs. Share this post Link to post Share on other sites
88high Posted June 15, 2012 I have that first piece in white from the cool convertible set... Share this post Link to post Share on other sites
commodore_legolas Posted June 16, 2012 In a few mocs I have seen, flames have been linked. So, I would really like to know how this is done. Thanks! Share this post Link to post Share on other sites
CMP Posted June 16, 2012 On the older version of the flame, there are 2 tiny pegs on the sides of the 4mm(?) area that can be locked into the curves of the flames themselves. Share this post Link to post Share on other sites
Lego Otaku Posted June 17, 2012 You need these: www.bricklink.com/catalogItem.asp?P=6126 not these: www.bricklink.com/catalogItem.asp?P=6126b Share this post Link to post Share on other sites
Cribs Posted June 17, 2012 Hello, I was wondering if anyone could explain how the person who built this castle built the tower. I don't understand how they made it circular while keeping the structural strength and how they attached the roof to it. Thanks! Share this post Link to post Share on other sites
soccerkid6 Posted June 17, 2012 These hinges: to make the round shape. And at the to attach the roof the builder probably put tiles on top of the wall section except where the roof could connect. Or the roof could just set there, or be hooked up from the center. Hope this helped Share this post Link to post Share on other sites
Palathadric Posted June 17, 2012 Wow! That is one impressive structure. Are there more pictures of it somewhere else on EB? Share this post Link to post Share on other sites
Cribs Posted June 18, 2012 These hinges: to make the round shape. And at the to attach the roof the builder probably put tiles on top of the wall section except where the roof could connect. Or the roof could just set there, or be hooked up from the center. Hope this helped Awesome. Thanks so much. I didn't know that piece existed. Wow! That is one impressive structure. Are there more pictures of it somewhere else on EB? There are a few more pictures. Here is a link to some pictures and a video of it: http://farm6.staticflickr.com/5102/5823622964_381b5095ec_z.jpg http://farm3.static.flickr.com/2256/5823059843_9415808d2e.jpg http://fc05.deviantart.net/fs71/i/2011/162/0/b/hogwarts_castle_legos_by_shippertrish-d3ioec1.jpg Thanks! Share this post Link to post Share on other sites
Vincent Kessels Posted June 20, 2012 Welcome to Eurobricks Cribs! Please introduce yourself in the Hello! My name is... forum. Are you aware of the Site Guidelines regarding image sizes? Share this post Link to post Share on other sites