ColletArrow Posted March 8, 2018 (edited) Introduction I've finally decided I need to do something with my enormous folder of pictures of old MOCs. That means uploading them to Bricksafe, and sharing them here! There's a few things I'd like to note before I start. Firstly, there's a fair amount of history amongst for me here; some photos are of my earliest train MOCs (although that was only 5 years ago). Therefore, as I post these, I should be able to show progression in my skills with building. Secondly, all of the models have been long since dismantled, frequently in order to build the next one! I worked with a very limited parts selection, and didn't often buy more bricks just for one model. Finally, sorry for the poor photography; my 'studio' was a north-facing living room with a white-ish carpet, which worked fine, but sometimes the background is cluttered or the lighting is odd. These weren't taken with uploading them in mind, so many I've had to hastily clean up in MS Paint! Hopefully they look OK. Anyway, on with the show. In this post, I'll present the 4 standard-gauge steam locomotives I've built over the years, in chronological order. 1. LMS Ivatt 2MT 2-6-0 Tender locomotive (August 2015) For my first steam locomotive (but not my first train, I'll show that later...), I thought I'd keep it simple; this is mainly based on the 79111 Constitution Train Chase, but suitably anglified. I think I used @zephyr1934's instructions for the cylinder/connecting rods mod, but with standard technic liftarms. I decided this boiler shape would look alright after seeing @Murdoch17's many variants! EB truly inspired this one, before I was even registered here. The numbers were based on a real locomotive in preservation, 46447, although with the BR logo replaced by "LRTS", as seen on the side of the Emerald Night. They were written on MS Word, printed out onto sticky labels and placed on the side! A really inelegant solution, and one that I regret to this day as the bricks still have them on or a sticky residue were I tried to take them off. At least they weren't over multiple parts. All the power functions elements were rammed into the tender, with only the LEDs on the loco itself. The battery box was controlled via the large dish representing the water cap, through which the green on/off LED could be seen. The headlamps were also movable, to represent some of the positions used in the British headlamp codes used to identify train types, hence the nest of wires under the smokebox. The bufferbeam itself got a little detail, complete with a non-LEGO part that slipped into my collection many years ago and I've never taken out. Finally, the cab even featured a full boiler backhead, not bad for my first attempt! Again, sorry for the awful pictures. Overall, not bad for a first attempt I don't think, even if it was essentially a 79111 extreme-mod. It got tested on a friend's small circle of track, and didn't perform badly if I remember correctly. If I were to build it again, I'd want to redesign the PF tender completely, maybe with the battery box on its side to get a lower profile. It was far too big for the tenders the real locomotives carry. The folder, and a few more pictures, can be found here: https://bricksafe.com/pages/Collet22/lms-ivatt-2mt. And now, onto: 2. BR (ex-GWR) 56xx Prairie 0-6-2 tank (September 2015) This model immediately followed the previous, and even used the same "stickers" (completely inappropriately, the GWR or later BR (WR) never used 5 digits on their locos!) but is clearly different in many ways. Mainly, I couldn't hide the PF in a tender, so the battery box was concealed behind the side tanks, the motor is just visible at the front, and the IR receiver took up the space in the coal bunker. I have no idea how well it performed as I only had about 6 pieces of track at this stage, but I get the feeling it wasn't good! I have obviously realised I needed the rubber bands by this point, it's a shame they were yellow. I think I was quite proud of how neatly the battery box access worked! I even crammed an opening hatch into the roof, not sure why: It had exactly the same cab interior, just slightly cramped by the IR receiver, so I won't show the picture. I believe this model also featured attachment points in all 4 positions for head/tail lamps, as before. Again, not bad overall, but I reckon I could do better if I built another one now. Especially the drivetrain, an M-motor connected directly to the wheels via 2 12-tooth bevel gears can't have worked well. I also recall I had difficulty with excess friction/resistance from the connecting rods and cylinders, that I never figured out before I dismantled it. Again, the folder is here: https://bricksafe.com/pages/Collet22/gwr-prairie-tank. 3. BR (ex-GWR) Pannier 0-6-0 tank (July 2016) It was only time before I had a go at one of these machines, they are probably my favourite steam locomotive! It also seems there was a break of about a year before this came about, but I think it was worth it. This build was created in LDD (and as such, I still have the .lxf file), I worked out what parts I already had, and then ordered the few I didn't already own. Mainly the many, many 1x2x1.3 curved-top bricks! This was my first train build in 6+ wide (with 7 for the cab). The tanks were fun on this one, the lower half being built upside-down, and entirely hollow to leave room for the battery box. Explore the .lxf file if you want to; I've uploaded it to the bricksafe folder. Again, the headlamps were moveable, although could only be illuminated by the LEDs when at the front. They could be placed in any of the usual positions. I didn't put much effort into the rest of the bufferbeam though, clearly! The challenge with this was definitely getting the motor in place. In the end, this mess is what I ended up with, the orange tiles meaning it couldn't quite get over level crossings. The blind drivers are held in place by 2736 technic axle towball with the ball cut off, a technique I saw @LEGO Train 12 Volts use I believe. Not purist, but I was willing to do that to 2 parts, 2 parts that have been used in many other things since. Again, it's a shame one of the rubber bands is blue. I don't think this setup gave poor performance, but I doubt it was particularly good either. Finally for this loco, here's a shot of the rear bunker, with "meshed" windows, hand rails and lamp attachment points. Once again, the folder with more images is here: https://bricksafe.com/pages/Collet22/gwr-pannier-tank. I've since revisited this one in LDD, attempting to rectify the motor problem. I don't think I've got a better solution yet, I might try to get an L-motor in the cab or something. 4. BR "USA" 0-6-0 tank (June 2017) I've saved the best (and most recent) until last. This one is actually still together! Once again, a new building style was tried; I found the blueprints online, overlaid it with a LEGO plates grid (in MS Powerpoint of all softwares, it's surprisingly useful!), and scaled it to the size of the wheels. I found it lined up almost perfectly, and started to build from there. You can quite clearly see the BB here, again hidden as low as possible behind the water tanks. The IR receiver is what's blocking the cab windows, and the m-motor is under the cab floor, connected to the 16-tooth gear just visible above the rear axle. The front boiler section also used the 79111 method: Again using one of the "stickers" from the first model, and with all 4 headlamp positions available. No LEDs this time though! You may also note there's only one steam pipe from the smokebox to the cylinders; evidently I never got around to finding the parts for the second! The water tanks chamfer is also somewhat representative, not having any longer slope bricks in my collection. This is by far my proudest part of the model, the cab windows. A fair amount of SNOT and LEGO maths was employed here to get it to line up, but it works! Shame there's nothing to see through them. The enormous hole in the roof was for the IR receiver. Finally, here's the rear of the loco. This was the worst part to build as I came to it last and was running out of parts, as emphasised by the lack of actual buffers! It does feature a "live" coal load though, the usual headlamp "brackets" and that non-LEGO part used for a brake hose connector. The full folder of pictures is available here: https://bricksafe.com/pages/Collet22/br-usa-tank. This model is still assembled, although stripped of it's PF components and with a proper boiler backhead instead. The drivetrain wasn't nearly as successful as I was hoping it would be, given the amount of reinforcement I added to it. Is it possible to build a good one with an M-motor, or should I get an L-motor instead for future models? Perhaps I should lower my expectations of LEGO models? I'm not really sure. Conclusion So, there they all are. I think a clear progression is visible between each model, but what do you think? If I were to build any of these again, how could I improve them? Also, did you enjoy this post? Should I post more like this? How could I improve my posting style? I've got a few more "themes" planned, such as diesel locomotives, narrow gauge trains, road-rail/hirail/whatever you call them vehicles... Edited March 8, 2018 by ColletArrow forgot to upload .lxf Share this post Link to post Share on other sites
Paperinik77pk Posted March 8, 2018 (edited) I love all of them! The solution you used in the 2-6-0 for boiler closing levers is very nice - may I use it on my clockwork locomotive #3? I would absolutely see more of these! Please go on also with narrow gauge trains!!! Edited March 8, 2018 by Paperinik77pk Share this post Link to post Share on other sites
Murdoch17 Posted March 8, 2018 Keep on posting them, as I love these. Can't wait for the diesels and narrow gauge! (Thanks for thew shout-out, by the way!) Share this post Link to post Share on other sites
CaL Posted March 8, 2018 Fantastic builds! Only thing left to do: Buy yourself a Buwizz. It will be really a relief, not cramming the IR receiver anymore into a space limited tank engine ;) Share this post Link to post Share on other sites
Vilhelm22 Posted March 8, 2018 Nice. There's definitely a change in quality between them. If you post more, can we see some pics of the train in your profile photo? I really like the look of that one. Share this post Link to post Share on other sites
ColletArrow Posted March 8, 2018 Thank you all for the nice comments. 2 hours ago, Paperinik77pk said: The solution you used in the 2-6-0 for boiler closing levers is very nice - may I use it on my clockwork locomotive #3? Feel free, it's only 2 parts after all. It probably came about by accident (many of my parts choices do) due to only sorting parts by colour. 1 hour ago, Murdoch17 said: Keep on posting them, as I love these. Can't wait for the diesels and narrow gauge! Thank you! 55 minutes ago, CaL said: Only thing left to do: Buy yourself a Buwizz. It will be really a relief, not cramming the IR receiver anymore into a space limited tank engine ;) Hmm. I've been thinking about this; it looks really good and I love the compactness, but it's waaay out of my tiny student budget unfortunately. 22 minutes ago, Vilhelm22 said: If you post more, can we see some pics of the train in your profile photo? I really like the look of that one. Yep, that'll be posted. Narrow Gauge seems the most popular, so I'll work on posting that tonight. Share this post Link to post Share on other sites
M_slug357 Posted March 8, 2018 yah, more Narrow Gauge! Share this post Link to post Share on other sites
Toastie Posted March 8, 2018 Good evening, (of course) I believe everyone here enjoyed your contribution! Just keep updating this thread - I am sure, it will gain a lot of attention and more importantly: Appreciation!!! ´With regard to your questions of how to possibly improve: "Be yourself. No one can say you're doing it wrong" (Charles M. Schulz). Just do it the way you feel comfortable with. It worked >perfectly well< with your "ColletArrow's old MOC thread" post. All the best, Thorsten Share this post Link to post Share on other sites
ColletArrow Posted March 9, 2018 Thanks both! I'll just carry on like this then, I guess. So, considering it's the most popular, here's the next installment of ColletArrow's old MOCs: Narrow Gauge. 1. Ffestiniog Railway Single Fairlie 0-4-4 tank (November 2015) My first proper Narrow gauge locomotive was essentially a copy of @jtlan's excellent version of this small articulated loco, seen here: https://www.eurobricks.com/forum/index.php?/forums/topic/101799-moc-narrow-gauge-single-fairlie/. I made a few changes; mainly, I built it in dark red and with smaller wheels. Clearly, it had no PF whatsoever. The connecting rods used that pair of technic towball axles with the ball cut off again; in fact, this was the model I first modified them for, not the GWR Pannier Tank earlier. A fair amount of blu-tack was also employed to improve the poor clutch power on the axles, as the train wheels are slightly wider than 1/2L annoyingly. Yet again, a detailed boiler backhead and live coal load. This time, the coal even went down a series of slopes to a chute inside the cab. I was very proud of that one. This last photo just about illustrates the articulation, where the driving wheels and cylidners are on one bogie, and the trailing wheels under the cab are on another. As before, the folder (complete with .lxf, if I remember to put it in) is available here: https://bricksafe.com/pages/Collet22/ng-ffestiniog-railway-single-fairlie#. 2. Freelance 0-4-0 Diesel locomotive (November 2015) This is the loco you've been seeing as my profile picture for the past year now! It was built at the same time as the above, and was my first PF-ed narrow gauge attempt. The loco only actually featured an m-motor and the LEDs, the BB and receiver were in the white van wagon behind. I'm pretty sure it was inspired by the BR Class 14 shunter with the center cab and low bonnets, but NG and with side skirts to hide the wheels. It's a shame the cables pushed the rear 'lid' up somewhat, it ruined the looks. A least the cab was fairly open. Surprisingly, it did actually run. It couldn't haul anything besides itself and the PF van, but it managed a reasonable pace. I figured later the main problem with it was that the heavy battery box was on trailing wheels, whilst there wasn't much weight above the driven wheels to provide traction. This inbalance is something I tried to address in the next model. 3. Lynton & Barntsaple railway 2-4-2 Baldwin tank 'Lyn' (March 2016) Whilst using the same parts and colour scheme as the Single Fairlie, this model is vastly different. For a start, it houses an M-motor, IR Receiver and LEDs, quite surprising given its diminutive size. Unsurprisingly, the side tanks and other parts weren't attached very well, and fell off quite frequently! Here's the model with some of the sides taken off: Both axles were powered, which was quite fun to set up with the gears and connecting rods. It's a shame the 1x6 technic brick was only in bright red in my collection. The universal joints leading through the rear axle were to provide transmission to the wheels under the battery box wagon it towed behind. The theory was that if more wheels were powered, especially those directly underneath the BB, it would perform better. I'm not sure that it did, but it was a good idea. Guess what, it's the return of those "stickered" bricks again! This time representing a wagon ID number, they seem to get everywhere. Overall, whilst this tiny locomotive looked good and should have run well, it didn't. It had a high tendency to fall over, and I don't think it ever ran for long periods. I'm not entirely sure how to get the center of mass lower, but that's my goal for next time. Meanwhile, here's the bricksafe folder with a few more photos: https://bricksafe.com/pages/Collet22/ng-lynton--barnstaple-railway-lyn. Conclusion Unfortunately, that wraps it up for my old Narrow Gauge photos. I do remember building an 0-4-0 diesel engine with a similar power arrangement at some point after these, but I don't seem to have any proper photos of it. It is in LDD though, so I should really build it again one day. As well as all this, I've been building a PF powered solo van in LDD. If I can build that and get it to work in real bricks I'll share it on here, but it certainly won't be soon so don't hold out for it. Next time... I think the next post will have to concern diesel shunters, I've got quite a progression of them. In the mean time, comments, criticism and questions are all welcome. Share this post Link to post Share on other sites