msk6003

Now wedo 2.0 hub almost become plastic trash.

Yes. sticker on multiple parts is bad. But at least you can cut using knife before disassemble. 180$ on that crane seems little expensive but considering number of cada unique parts I think that is fair enough. Ignore it. 42141 Mclaren F1 and 42098 Car transporter is 180$ lego technic set. Seems those crane is little overprised but not so much. 160~170 will best to me.

I still waiting Fiat 131 abarth rally car and efferman's crane. Hope cada make more rally car in future. https://decadastore.com/products/cada-military-crane-truck-c61507w @efferman's crane can now buy in cada offical site. Can I get the part list?

Basically both use same battery component so it will work with screw type. And how about using the extra space to route the charging port to the bottom with a USB-C extension cable?

Considering original bike's part is green and that list don't display full part list, I still belive it is real green.

For some strange reason, green round 1x1 tile is also rare. Include 17 in globe, 7 in promotion, 1 in 2023's friends model. Looks like yes.

Finally TLG bring back double bent liftarm in green. Last release is 2002 but it is education set so actual last release is 1998. Included set 8x in 8479(1997) 2x in 9780(1998) 2x in 970676(2002) 2x in 8217(1998) 9780 and 970676 is education set. And angle connector #6 in green is also very rare parts. Last release is 1999.

Personally, I was bored with Monster Jam even three years in a row. It had the same tires, a similar chassis structure, and the only thing to salvage was rims and parts in rare colors. At least it would have been welcomed to me if the Bone Shaker truck had come out, but it was impossible due to Mattel (Hot Wheels) holding the license.

I think that not only tapered panels but also grooved flat panels are very useful parts. There are parts of the model I'm building that can't be replaced with Lego flat panels, and as far as I know, Efferman's crane model also uses those part. P.S - My model is almost finish. Need to work only in front parts. Function - 4wd drive with 2 buggy motor(can choose speed while building), L4 engine(but something is different with other car) front wheel steering, independent suspension, detachable bonnet and engine cover.

Maybe someone will make this as RC model. If no one do it, I will.

Almost give up. To busy for work. damn it

I know this is funny and weird. Just accept this as joke. Hyundai reported that the N vision 74 vehicle will be released between 2024 and 2027 in a limited edition of 100 units. Cause this is not that famous, iconic and electronic hybrid, so not suitable for technic. But anyone can dream.

In my opinion, the difference in appearance between this set and the actual vehicle already goes beyond the level of 'it's okay because it's a toy.' It would have been better if it had just been called ‘John Deere harvester.’

Because B&P service is not available in every country, that is not perfect answer. South korea is one of that country which can't use B&P.

Like this(new part highlighted in lime) but unlike my first thought wheel position is same with 3pin hub and in those setup suspension movement is very small cause 1x3 half thick beam will rub suspension arm. Maybe it only useful for non-suspended axle or live axle setup.

I never thought about that! Cause 3pin hub is longer than this part, I think it is still useful for car which use 56908 wheel and maybe if we use half stud thick beam like 5L or 7L, it also can work as suspended steering with driving hub.(Mustang's 5 spook 30x20 wheel will not fit)

That will be very useful for make GBC rail.

Finally TLG made 68327 wheel's black version. I can't wait to get 4 of this for my drift car moc.

I bought C63004 Yellow car and built recently. And I found cada's 1/2 bush can work as double sided anti stud plate! TLG's 1L bush has some cutout on one side which can fit between 4 stud. Cada's 1L bush also has it on one side but for some reason, cada's 1/2 bush has cutout on both side which make it work as double sided anti stud plate.

Yes that parts. And I caculate cada buggy motor's inside/outside output gear ratio is 1.3. Actually slightly bigger like 1.3254532(forget exact number) but still very similar with 1.3.

Is anyone know where can buy Cada special parts? I know cada offical store but there has only few special parts. It lack all kind of frame, panel, T and I beam and especially electronic separator which included in AMG one.(which is what I need one now)

That is why I don't like separate wheel for drive header. And for me, that is MUCH more unrealstic than header rotating direction. By the way, 16t can drive 28t with no problem. Only problem from those combination when it take lot of stress, gear can skipping easly. But in this model it can ignore.

Stop just talking and build yourself and show us.

42078 Mack has second steering wheel(for B model) inside of cabin top. Kid will think real truck also has second steering wheel inside top of cabin.

42036 Street motorcycle don't have radiator and breake. If children who played with this set grow up and ride a motorcycle, they don't understand why need brakes and why a radiator is needed, and they will blow the engine and die in an accident. 42092 Rescue helicopter don't have propeller pitch angle on main rotor. If children who played with this set grow up and repairing helicopter, they don't understand how can fix it's main rotor. And both this model is 40$ like set. Let's stop this useless conversation. This is toy. And most toy don't that accurate like million dollar scale model. If you want to continue talking, why not design a header that fits the model size yourself and bring it in?