centering a half bush on a 2L axle?

[SNIPE]

Hi

Does anybody have an LDD trick to place a half bush in the very center of an axle?, its easier to see with 2L axle if its centered properly or not.

regards

Edited July 2, 2013 by SNIPE

[Calabar]

Did you tried to built a scaffolding using a brick with a stud in the centre?

[SNIPE]

No, what sort of scaffolding ? with axles or beams or bricks or?

[Calabar]

Oh, everything could be suitable!

I'll try something later, if I'll have a bit of time.

[Alasdair Ryan]

Could you use this part below as a guide for adding bushes?

[SNIPE]

The problem is that the grid spacing or part movement is not fine enough, 0.5L has 6 possible places it can be in in that space.

so If I put two on an axle and kept moving one of them, there would be 6 places would would be in before the gap between the other one is another 1.5L

I need to get it into half of one of those spaces really but even the stoppers on some axles is worth 1 space so they aren't fine enough.

I'm not sure how to use this 4L lift-arm as it too does the same thing as the bush I want to get in the middle of the axle. and the lift-arm has no odd lengths on it

[Lipko]

Maybe you could try it with chain link pieces.

Maybe I'll post something if I can soon

Wait, there are many half-stud offsetting pieces, why don't you try one of those?

EDIT: okay, it is an interesting puzzle

Edited July 3, 2013 by Lipko

[Nachapon Lego]

Can not be done by normal method because the minimun move in LDD is 1/10 stud = 0.8cm / 10 = 0.08cm, but this case have to move 1/20 stud = 0.04cm.

Use LXFML edit trick to add or minus Y value of the bush by 0.04.

LXFML edit trick:

http://www.eurobrick...0

canter by Nachapon S., on Flickr

Edited July 3, 2013 by bbqqq

[SNIPE]

Thanks x1000

[Nachapon Lego]

I will post another trick for move parts 0.01 cm without edit lxfml soon.

Edited July 4, 2013 by bbqqq

[Nachapon Lego]

This trick is almost as accurate as LXFML edit trick, but easier.

Ldd trick #4: Precise move pieces for about 1/80 stud every times (0.01000016927719116 cm)

Edited July 4, 2013 by bbqqq

[SNIPE]

Hi,

Thanks again, the LXFXML trick is just a pain in the mouth to do, I wish they would fix this stupid bug

In the mean time ill use that trick you posted with the brown lego plates.

Thanks for everything.

Edited July 7, 2013 by SNIPE

[Calabar]

This trick is almost as accurate as LXFML edit trick, but easier.

Ldd trick #4: Precise move pieces for about 1/80 stud every times (0.01000016927719116 cm)

I tried it but no success.

Maybe it works with "outline bricks" enabled only?

Or maybe I miss something?

[Nachapon Lego]

Hi,

Thanks again, the LXFXML trick is just a pain in the mouth to do, I wish they would fix this stupid bug

In the mean time ill use that trick you posted with the brown lego plates.

Thanks for everything.

You are welcome.

I tried it but no success.

Maybe it works with "outline bricks" enabled only?

Or maybe I miss something?

Did you also tried TRICK #4.1 as below? (I tried to post link only but it lead to different reply.)

Edited July 8, 2013 by bbqqq