Zerobricks Posted November 29, 2019 Just now, Ghosty627 said: I can't upload file anymore ... can I send a private message ? Sure, or you a website like Bricksafe to host your photos like I do. Share this post Link to post Share on other sites
Ghosty627 Posted November 29, 2019 (edited) 39 minutes ago, Zerobricks said: Sure, or you a website like Bricksafe to host your photos like I do. Here is a dropbox link just for 3 minutes ... Edited November 29, 2019 by Ghosty627 Share this post Link to post Share on other sites
Zerobricks Posted November 29, 2019 1 minute ago, Ghosty627 said: Here is a dropbox link just for 3 minutes : https://www.dropbox.com/sh/vz41befzq0864nc/AAB-_R-bQqwXRdbJFbhDFafka?dl=0 Here is your problem, remove the grey 1x1 beam which is hitting the hub: Share this post Link to post Share on other sites
Ghosty627 Posted November 29, 2019 (edited) I removed the beam ... I add 2 new photos 10, 11, 12 The angle is the same ... Edited November 29, 2019 by Ghosty627 Share this post Link to post Share on other sites
Zerobricks Posted November 29, 2019 1 minute ago, Ghosty627 said: I removed the beam ... https://www.dropbox.com/sh/vz41befzq0864nc/AAB-_R-bQqwXRdbJFbhDFafka?dl=0 I add 2 new photos 10 and 11 The angle is the same ... Something is blocking your steering rack from moving all the way. Check what the hubs are bumping into. Wait. You are using 3L axles with studs to hold the steering arms? They are blocking the travel, because they are going through the rack and bumping the triangle brick behind it. Pull the axles holding the steering arms out by half a stud. Share this post Link to post Share on other sites
Ghosty627 Posted November 29, 2019 8 minutes ago, Zerobricks said: Wait. You are using 3L axles with studs to hold the steering arms? They are blocking the travel, because they are going through the rack and bumping the triangle brick behind it. Pull the axles holding the steering arms out by half a stud. YES !!! That was the issue !!! Much thx for your great support !!! Share this post Link to post Share on other sites
Zerobricks Posted November 29, 2019 Just now, Ghosty627 said: YES !!! That was the issue !!! Much thx for your great support !!! No problem, glad to help Have fun with the beast! Share this post Link to post Share on other sites
Ghosty627 Posted November 29, 2019 36 minutes ago, Zerobricks said: No problem, glad to help Have fun with the beast! This 6x6 offroad vehicle is realy a beast. He clims a gradient of 53 degree Share this post Link to post Share on other sites
Ghosty627 Posted November 30, 2019 @Zerobricks you are fine, when I release my version, based on this 6x6, with some modifications ? Share this post Link to post Share on other sites
Zerobricks Posted November 30, 2019 Just now, Ghosty627 said: @Zerobricks you are fine, when I release my version, based on this 6x6, with some modifications ? Sure, as long as you credit the original designer Share this post Link to post Share on other sites
Ghosty627 Posted November 30, 2019 Just now, Zerobricks said: Sure, as long as you credit the original designer Sure !!! Share this post Link to post Share on other sites
Zerobricks Posted April 6, 2020 (edited) Thanks to a Chinese fan by a name of Kyon, the instructions for the Tiger 6x6 are now available in PDF: https://drive.google.com/file/d/1iub0olYMmVF50ZHELJHo5OIqw_8YRZri/view And in Stud.io: https://drive.google.com/file/d/1s-L5n1L8Pgr0weH3Z03Y4rko9qeQD0_w/view Edited April 6, 2020 by Zerobricks Share this post Link to post Share on other sites
amorti Posted April 6, 2020 (edited) Ok... Instructions from China. So when are mould king releasing it? Edited April 6, 2020 by amorti Share this post Link to post Share on other sites
AussieBrett Posted June 26, 2020 On 11/30/2019 at 9:43 PM, Zerobricks said: Sure, as long as you credit the original designer I've jumped on this bandwagon too, but don't have the budget for the buggy motors so a different system will be going in, along with a colour change. Share this post Link to post Share on other sites
AussieBrett Posted September 24, 2020 (edited) First mock-up done, only has the 2 speed gearbox and 2x L motors at the moment. Embarrassingly, I didn't realise till most of the body was done that it was the same colour scheme as the 42070 6x6 tow truck. Have also built it as a quick remove body for now, may not be feasible longer term. Edited September 24, 2020 by AussieBrett Share this post Link to post Share on other sites
Zerobricks Posted September 24, 2020 14 minutes ago, AussieBrett said: First mock-up done, only has the 2 speed gearbox and 2x L motors at the moment. Embarrassingly, I didn't realise till most of the body was done that it was the same colour scheme as the 42070 6x6 tow truck. Have also built it as a quick remove body for now, may not be feasible longer term. Looking good! Share this post Link to post Share on other sites
Maniac42099 Posted July 13, 2021 (edited) I'd like first, to thank you for this post and sharing the instructions. The Tiger is my favourite out of all my toys. ❤ I'm also here to share my very simple modification to change the rear universal joints to the new, much stronger ones. https://imgur.com/gallery/E5WONxz Edited July 13, 2021 by Maniac42099 Share this post Link to post Share on other sites
amorti Posted July 14, 2021 8 hours ago, Maniac42099 said: I'm also here to share my very simple modification to change the rear universal joints to the new, much stronger ones. https://imgur.com/gallery/E5WONxz That'll work! However, while those joints won't snap, they do wear out after a while. Metal joints would work better. Share this post Link to post Share on other sites
nervousman Posted September 29, 2021 (edited) Hey, I built this monster about six months ago. From the beginning, I had a problem with shifting gears. Until now it has operated in ldcr mode, now it does not change at all. I thought the problem was the M motor but changed to a new one out of the box and it's the same. Anyone have an idea where the bug might be? I checked all the gears during the engine swap and they seem to run smoothly ... Edited September 29, 2021 by nervousman Share this post Link to post Share on other sites
Zerobricks Posted September 29, 2021 45 minutes ago, nervousman said: Hey, I built this monster about six months ago. From the beginning, I had a problem with shifting gears. Until now it has operated in ldcr mode, now it does not change at all. I thought the problem was the M motor but changed to a new one out of the box and it's the same. Anyone have an idea where the bug might be? I checked all the gears during the engine swap and they seem to run smoothly ... Hmm, interesting. Make sure both geraboxes are properly synchronized. Share this post Link to post Share on other sites
nervousman Posted September 30, 2021 I checked it 2 times when replacing the engine, it's not that. :( Share this post Link to post Share on other sites
CooolWollf Posted July 6, 2023 (edited) I'm trying to build my own version of this but can't for the life of me figure out how to get the shock absorber in to the build, have someone tips for me? Here is my version so far in to the build https://drive.google.com/drive/folders/1gxrk8a2PHI1X9OsuOKcgWSjcGv0x-CV7?usp=drive_link Edited July 6, 2023 by CooolWollf Share this post Link to post Share on other sites
Zerobricks Posted July 7, 2023 18 hours ago, CooolWollf said: I'm trying to build my own version of this but can't for the life of me figure out how to get the shock absorber in to the build, have someone tips for me? Here is my version so far in to the build https://drive.google.com/drive/folders/1gxrk8a2PHI1X9OsuOKcgWSjcGv0x-CV7?usp=drive_link Which shock absorbers are you referring to? Also, you posted a private Google Drive link. Share this post Link to post Share on other sites
CooolWollf Posted July 7, 2023 (edited) 4 hours ago, Zerobricks said: Which shock absorbers are you referring to? Also, you posted a private Google Drive link. I have the red ones that are similar to you'res This should work https://drive.google.com/drive/folders/1gxrk8a2PHI1X9OsuOKcgWSjcGv0x-CV7?usp=drive_link Edited July 7, 2023 by CooolWollf Share this post Link to post Share on other sites
Zerobricks Posted July 7, 2023 I'm sorry, but that doesn't look like my project? Share this post Link to post Share on other sites