General Part Discussion

[anyUser]

Is there an explanation why panels and do not properly align?

When building the Bugatti I found:

e.g. the angled panels stick out by 0.5(?) mm. The same holds for the 2x1x1 panel.

 

Edited March 26, 2023 by anyUser

[Jurss]

It is OK, accroding to latest lego quality standards, like colour variations, misaligned axle holes etc.

[Ngoc Nguyen]

  On 3/27/2023 at 4:15 AM, Jurss said:

quality standards,

Expand  

You mean quality substandards

[gyenesvi]

Haven’t noticed this before but it looks the same for me, sadly..

[keymaker]

Same in my case... But why they can align small old panels and they cannot new ones?

[Mikdun]

  On 3/25/2023 at 3:25 AM, Bricktrain said:

It could be that different colours have different sizes, some colours shrink more from manufacturing.

If you use the other bottom and top parts are they much looser?

I found that track links are different lengths for the same number of links, changing from black to grey meant the sprockets had to be moved to keep the track tension the same. 

Expand  

Different shrinkage for me, don't believe they created different sizes for different colours.

Would be interesting to hear weather the other two halves make loose connection - they should.

[anyUser]

  On 3/27/2023 at 10:14 AM, Mikdun said:

Would be interesting to hear weather the other two halves make loose connection - they should. 

Expand  

I did a quick check with two of my parts

  On 3/26/2023 at 8:45 PM, anyUser said:

  (obtained from Bricks & Pieces) and from rear spoiler of 42151

Expand  

Test setup: Attach each part on the end of a 5L axle (taken from my parts, so special selection) hold each piece with a hand and pull in the direction of the axle:
Which part will come off from the axle?
I switched over sides of the axle and, because first result appeared to be biased, also changed between left and right hand.
Results were unconclusive.

[Mikdun]

  On 3/27/2023 at 9:01 PM, anyUser said:

Test setup: Attach each part on the end of a 5L axle

Expand  

I was talking about the thin hinges shown by MP LEGO Technic creations.

[Bricktrain]

  On 3/27/2023 at 10:14 AM, Mikdun said:

Different shrinkage for me, don't believe they created different sizes for different colours.

Would be interesting to hear weather the other two halves make loose connection - they should.

Expand  

Someone once wrote that there can be different molds for different colours as they shrink by different amounts when they cool.

[Mikdun]

  On 3/29/2023 at 9:11 AM, Bricktrain said:

Someone once wrote that there can be different molds for different colours as they shrink by different amounts when they cool.

Expand  

Every plastic shrinks when cooled. From my experience there can be measurable difference between the same resin with different colour.

Making different moulds will mean that each colour will have the same final dimension - possible to do, but very tedious and only advantageous when mixing moving parts' colours.

[Maaboo the Witch]

77015 Temple of the Golden Idol features a banana gear rack in dark grey.

Edited April 2, 2023 by Maaboo35

[Jockos]

  On 4/2/2023 at 4:47 PM, Maaboo35 said:

77015 Temple of the Golden Idol features a banana gear rack in dark grey.

Expand  

I'm curious whether it'll be used in the Liebherr, or any of the summer sets

[LvdH]

No idea what you’d use it for, but the blue thing is new.

[Zerobricks]

Oh, wow, nice find! They do look a bit like counterweights!

[Ngoc Nguyen]

Hooboy what is that humongous quarter eclipse liftarm piece?! Does it signal the coming of XXL panels in Technic?

Edited April 19, 2023 by Ngoc Nguyen

[Zerobricks]

I think it should fit the curvature of the 3x13 curved panel.

Edited April 19, 2023 by Zerobricks

[Ngoc Nguyen]

  On 4/19/2023 at 12:38 PM, Zerobricks said:

I think it should fit the curvature of the 3x13 curved panel.

Expand  

The only diagonal and barely legal way of putting a 3x13 curved panel is between 6 studs high and 12 studs long, and that quarter piece doesn't have those dimensions.

[anyUser]

  On 4/19/2023 at 12:38 PM, Zerobricks said:

I think it should fit the curvature of the 3x13 curved panel.

Expand  

It's only 9M wide. (From Pythagoras) the long side would measure < 10M. How would that match?

[Zerobricks]

I meant the curvature- radius, not length. I know the length doesn't fit at all, it's only 9 studs long and panel is 13-2.

[SNIPE]

Ah, youse beat me to it 🙂, I found that new panel today on YouTube and yeah it looks interesting for making car splitters and other bodywork

[Davidz90]

Not only that, this large quarter ellipse will be amazing for all sorts of structural purposes. It should easily survive forces that would break a regular liftarm. 

[astyanax]

In the antlers, looks like some shade of blue for 10197?

Source

[Void_S]

Medium blue, I suppose... Excellent addition to Megalodon (who knows - may it be someone's Patronus? )

Also, I see not new but still nice friction 1/2 studs that hold the horns.

[Maaboo the Witch]

Also medium blue macaroni parts.

[zoo]

...and angled connector.