Search the Community
Showing results for tags 'Tydirium'.
Found 4 results
barneius posted a topic in LEGO Star WarsMy model of Lambda-class Imperial Shuttle was created from scratch and it is based on the construction solutions of the 75094 set. First it was created in LDD and later, after ordering the bricks, I made a number of significant adjustments. The biggest challenge was to keep the proportions as decent as possible, which, apart from the limitations resulting from the use of the 75094 skeleton, does not seem to me to be a simple thing on this scale. Among other things, for this reason, I finally gave up the opened interior (on which I did not particularly care about). Wherever possible, I tried to reproduce or refer to the details of the original. You may attach the landing gear but my model will always be presented on the stand. It is very stable and consists of about 1600 parts and therefore roughly over 600 more than the progenitor. I have designed the wings from the beginning in SNOT. The body is two studs longer, and in a large part, is a completely different construction than 75094. The wings are better embedded in it and they are less swaying, which is important because they are heavier. The fin is also proportionally extended by two studs and embedded somewhat differently. I have managed to slim down the cockpit and get a minimal nose down reduction in relation to the bottom, keeping the place for the stressed Han Solo. In this scale in flying mode, it matches the height of the UCS Slave I and it is the optimal scale for this model for me. 10212 UCS in flight position (and this is the only way I imagine presenting it) is monstrously huge - I mainly mean the height. I think that my model next to the UCS would not be too ashamed. You will find more photos in my flicker album here: https://flic.kr/s/aHskvtke2v Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr Lambda-class Imperial Shuttle by Barney Markowski, on Flickr
This is my take on a minifig-scale UCS scale Imperial Shuttle from Return of the Jedi. Since I wasn't sure where to start, the worm gear mechanism is loosely based on the official set. However, the rest is a mix of my design with subtle cues taken from Marshal Banana's MOC and 10212. It features gear-driven wings, detachable landing gear, poseable weapons, and an opening canopy with room for 4 minifigs.
In the occasion of the new Imperial Shuttle 75094 I virtually rebuilt two movie scenes from Star Wars Episode VI - Return of the Jedi - showing the iimperial Shuttle Tydirium approaching Endor. The model was built with LDCad and rendered with Pov-Ray. Imperial Shuttle Tydirium by papacharly24 Imperial Shuttle Tydirium approaches Endor by papacharly24 Hope you enjoy it!
Up next in my series of Kenner Mini-Rigs from the 80's, is the ISP-6, Imperial Shuttle Pod. This is basically a mini version of the Imperial Shuttle seen in Return of the Jedi. The ISP-6 Imperial Shuttle Pod, was a small air/space vehicle used by the Imperial forces. A single-seat vehicle with a tri-wing configuration reminiscent of the larger Lambda-class shuttle, the ISP-6 was probably designed by Sienar Fleet Systems or Cygnus Spaceworks. It was a fast, compact transport, designed to be deployed from larger shuttles, and it was armed with two defensive blaster cannons for operations in combat zones. It also possessed a rear-view mirror to spot Rebel fighters from behind. After building is and getting the proportions about right, I looked and there was enough room for Vader as well as some cargo. I put a passage behind him, but, that may change when I build this early next year. Then again, I may have an Imperial Pilot fly this and have Vader kick back and relax while he does all the work. Going back to my MLC-3. The proportion of Lego mini-figs and Kenner Star Wars figures is way different. This design may fit an old Kenner fig, but, it's Lego so I may go with 2 figs in it. Wings up, landing gear down. Roomy?! There are 2 hinges on the top canopy, to access the whole interior of the ship. Wings fold up and down. Landing gear doesn't fit in the ship, it's too small of a build, they need to be taken when swooshing this around. I'm not completely happy with the nose. I may work on this later, but, I like it and think it fits in with the rest of the Kenner Mini-Rigs, thus far. I attacked the file to this if anybody would like to look at it or try to build this. This model is the second largest Mini-Rig I built, with 332 pieces in it. The MTV-7, has the highest pieces count, the MTV-7, Multi Terrain Vehicle will be posted tomorrow. Thanks for looking, Jamie 9 - EU - Mini Rig - ISP-6 - Imperial Shuttle Pod.lxf