Al Ex

Xbox Controller attached configuration codes for almost all models (42100 Liebherr Excavator R 9800 missing) - Lego 4X4 X-treme Off-Roader (42099): https://pybricks.com/project/technic-42099-xbox/ - Lego Top Gear Rally Car (42109): https://pybricks.com/project/technic-42109-xbox/ - Lego 4x4 Mercedes Benz Zetros Trial Truck (42129): https://pybricks.com/project/technic-42129-xbox/ - Lego Off-Road Buggy (42124): https://pybricks.com/project/technic-42124-xbox/ or https://vk.com/wall649079923_28 - Lego Audi RS Q e-tron (42160): https://pybricks.com/project/technic-42160-xbox/ or https://github.com/orgs/pybricks/discussions/1533 - Lego Liebherr LR 13000 (42146) (Top hub connects to Xbox controller, bottom hub receives the control data from the top): https://github.com/orgs/pybricks/discussions/1505 - Lego Transformation Vehicle (42140): https://www.tcm0.tk/2024/02/xbox-bluetooth-controller-konnen-nun.html or https://github.com/orgs/pybricks/discussions/1576- Lego Volvo-Dumper (6x6) (42114): https://github.com/orgs/pybricks/discussions/1466 - Lego Cat® D11 Bulldozer (432131): https://pybricks.com/project/technic-42131-xbox/

Xbox Controller attached Codes: - Liebherr LR 13000 (42146) + Xbox Controller: https://github.com/orgs/pybricks/discussions/1505 (Top hub connects to Xbox controller. Bottom hub receives the control data from the top) - Audi RS Q e-tron (42160) + Xbox Controller, v.1: https://pybricks.com/projects/sets/tech ... ontroller/ - Transformation Vehicle (42140) + Xbox Controller: https://www.tcm0.tk/2024/02/xbox-blueto ... n-nun.html- Volvo-Dumper (6x6) (42114) + Xbox Controller: https://github.com/orgs/pybricks/discussions/1466 - Cat® D11 Bulldozer (432131) + Xbox Controller: https://github.com/orgs/pybricks/discussions/1546

pybricks: „As you could see it hinted in the video, it does work with multiple hubs, you can e.g. control the Liebherr crane as well that has 2 hubs.There'll be more publications about the functionality and how it can be used, make sure to follow the Pybricks social channels. There is no limit, so 10 hubs will also work!“ How it works see older code for Liebherr + Lego 88010 remote: „Put the program on both hubs. Upon starting the program the hub will search for a remote for 5 seconds, after that it will assume the other hub has the remote, so it will go into bluetooth receiving state.So turn on both hubs, turn on the remote, one hub will connect to the remote, the other will receive commands over bluetooth, it doesnt matter which hub has the remote.“ https://github.com/orgs/pybricks/discussions/1447

Compatible: XBOX One (Revision 2, ….) XBOX Series Generation XBOX Elite 2 Controller Not compatible: - First XBOX One (Revision 1) - First XBOX Elite Controller

Controller support Bluetooth Low Energy (BLE): New Xbox Series Controller support Bluetooth Low Energy (BLE), in my opinion the best BLE Controller because of proportional steering and two choices for batteries: AA batteries or rechargeable battery pack (For the sake of completeness the older Xbox One Controller support Bluetooth Low Energy (BLE) after Firmware Update, see Video)

I search a easy modification to lower down the rear axle..

Hi Polarkicht, can you upload a picture from your support bracket solution, thanks

See here, Pybricks Firmware for Lego Hub, direct control with Lego 88010 RC + Firmware Tutorial

Pybricks + Iphone: Works also, tested with Bluefy Web BLE Browser (with BLE interface) and CAT Bulldozer

the new pybricks HUB Firmware from technicmaster0 works with Powered Up 88010 RC & the buttons change the direction after rollover (Hub Position Sensor)

yes, documentaion is clear enough, i printed out the 2 sites with BLA modes to have easy access at any time

very nice, thanks! tested it with my CAT Bulldozer. I Hope Pybricks also supports other BLE (Bluetooth Low Energie) controllers in the future, for example the Xbox Series Controller with proportional control

I hope iit’s the red LeMans Hypercar with Ferrari prints, without promotion on it and with transparent engine, engine hood

I think the best way is to use the ladder manuell and the Rc function for the 2 new Ripper actuators or manuell switch between Rc ladder and Rc Ripper actuators

@ABCampos thanks, the idea with LED function indicator is very clever