flashtom Posted November 18, 2014 Posted November 18, 2014 (edited) hello everyone, i have a problem on 8110's front bridge. It seems a bit excursion, and i havn't found where i was wrong. i try to backout the black joint lever, it will be OK. help~~~ Edited November 18, 2014 by flashtom Quote
DrJB Posted November 18, 2014 Posted November 18, 2014 A bit difficult to understand what the issue is ... can you elaborate a little more? Quote
flashtom Posted November 18, 2014 Author Posted November 18, 2014 A bit difficult to understand what the issue is ... can you elaborate a little more? First of all thank you. 8110's front bridge was deflection to right. Not in center. I don't know why. The process was all follow by user guide step by step. Quote
TheItalianBrick Posted November 18, 2014 Posted November 18, 2014 ok, probably I have the answer. The front "bridge" it's hold by a pin and an arm bush. Make sure the pin it's in the right hole...cos there are 2 holes close to each others.....if you put it the wrong one it will skid the all axle. Quote
dougstar Posted November 18, 2014 Posted November 18, 2014 hello flashtom not exactly sure why its not centered. im going to take a guess that your shocks have not been put on both the same way. check in book two were the shocks attach to the front of the chassis page 71 step 97. hope this helps, it may help with a few more pics doug Quote
zweihander Posted November 18, 2014 Posted November 18, 2014 Are you talking about the front axle being a little to the right side when the suspension is not compressed? If so, that is the way it is intended to be. The reason is to make the front axle stay in the center when the suspension is compressed. Quote
flashtom Posted November 18, 2014 Author Posted November 18, 2014 ok, probably I have the answer. The front "bridge" it's hold by a pin and an arm bush. Make sure the pin it's in the right hole...cos there are 2 holes close to each others.....if you put it the wrong one it will skid the all axle. Thank you. That pin is in correct hole. hello flashtom not exactly sure why its not centered. im going to take a guess that your shocks have not been put on both the same way. check in book two were the shocks attach to the front of the chassis page 71 step 97. hope this helps, it may help with a few more pics doug Thank you dear. :D Quote
Zerobricks Posted November 18, 2014 Posted November 18, 2014 ITS NORMAL Pahnrod is at an angle and it slightly pulls the axle sideways. Quote
Imanol BB Posted August 4, 2015 Posted August 4, 2015 (edited) Hi, here is the solution to make the axle be in the most center place: http://www.brickshelf.com/gallery/imanolB/unimog/p1120669.jpg (used in the rear axle): http://www.brickshelf.com/gallery/imanolB/unimog/p1120672.jpg and the proof: http://www.brickshelf.com/gallery/imanolB/unimog/p1120676.jpg http://www.brickshelf.com/gallery/imanolB/unimog/p1120677.jpg hope this works for you. Edited August 4, 2015 by Blakbird : removed massively oversized images. Quote
TheNextLegoDesinger Posted August 4, 2015 Posted August 4, 2015 (edited) please don't bump maybe you should repost this in the 8110 mods topic good idea though TNLD Edited August 4, 2015 by TheNextLegoDesinger Quote
Imanol BB Posted August 4, 2015 Posted August 4, 2015 ok, i have just post it on Unimog 8110 mods and improvements, should i delete my previous post? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.