lombardini003

Well answering my own question here, I think I figured out light direction. And I've downloaded another PDF reader and it's working perfect now. Happy Easter everyone.

Good morning. That violet pictured item is the L motor. I have downloaded the instructions on my daughters laptop, however, some further help please, when I download the moc, it is instantly downloaded by google drive, its also too large a file for Google drive but downloads anyway but not in full, it misses a few pages here and there. When you download it yourself, by what program does it download? Secondly, I noticed the pf light installation, how do I know which direction to Install? thanks again.. Also, every time I re download the instructions I get a few more pages I did not get the previous attempt but it seems like the instructions crash after 40 minutes..

Hello again. like I said before I am missing a lot of pages.. page 1010 I'm ok, page 1011 I'm missing and then pops up page 1013 with this entire section in violet already made?? Where did this parts section come from? Picture below. sorry I could not attach picture because it was too large.

Ok thank you. Great build thus far! Silly me- we have already built the boom and stick, and it's all black. Today we start the superstructure. Thanks very much.

Hello. Wondering if this red part is 32009?. If it is - it's not in the parts liSt. Thanks.

Hi, finally building this weekend with my son. I built the entire base. We started building the arms, however, every 2nd page in PDF format and Adobe is blank, thus leaving us guessing what parts are required. Anyone else experiencing this problem. Great build thus far Sheo. Thank you!

Sounds promising!! Perhaps some of us will be able to build This masterpiece. Well done and thank you for sharing everything already. As my son and i are currently building the great terex rh400 by sheo. Sheo has shared his building instructions with all!! Thank you very much.

Finally received all the parts including 53533. I noticed a few different versions of undercarriage?

Beautiful moc. Can you give us a closer clear picture of your controller. Thank you.

Oh OK Sheo. I guess it's not needed?

Sorry Sheo. I don't understand. From your instructions, 53533 is fully utilized.

Just got home and tried using the other part you suggested. Doesn't look like it's going to work- the single hole missing like in 53533 is being used in your design. Pg11. Thanks anyway.

Sheo, I see that you are using 2 axles 2 beams and 1 connector with hole. I assume the single hole near connector on 53533 is not used? Also, is it ok that the connector part will rotate as its not solid? Thank you.

Simply stunning Sheo! I noticed you had a detour from part no 61905. Do you have a detour for part no 53533? I collected all parts from Lego shop and toypro. Only bricklink has 53533. I do not have a paypal account and therefore cannot buy this part x 4. I have all parts except 53533. Any suggestions? And again an exceptional technic moc!!! Well done..

and also, i need to incorporate all this to just 2 levers in some way.. even if i use 3 or 4 contollers, at the end point it must be controlled via 1 left, 1 right joystick and all work simultaneously, i have seen on this board many interesting controllers where they are using many controllers all hooked up to either one or two controllers.. check this site, http://www.technicbr...ts-of-your.html -this will be interesting. thank you very much for the replies. i am actually building the liebherr that Milan has built and want to be able to operate the machine like a skidsteer and be able to drive, lift lower and tilt bucket all at the same time but regardless how many controllers i use - at the end it must be controlled via just 2 levers.. Milan liebherr has 2 xl motors running the tracks, 2 m motors lifting lowering the bucket running the same time controlling 2 LA, and one m motor for tilting bucket. hope this helps. thank you.

Interesting. Do you have ir controllers with this and are the ir controllers set up to operate like the real machine? I am looking for a proper ir controller set up to operate like the real machine. Thank you.

H style controls. 2 xl motors for the tracks, 2 m motors lifting and raising the bucket, 1 m motor tilting the bucket. And now need help to relay this to the ir controllers. Thank you.

Hi. Thanks for the replies. I will build a skid steer / cat 973D - both these machines use the exact same controls. I will use tracks. I would like to use the exact controls and also move the same as the real machine, I assume I will need two ir controllers and i need the Help to properly set up the ir controllers. Thank you.

hello everyone. i am in need to build a skid steer with total power function controls. the controls have to be identical to the real skid steer controls. does anyone have any info or links to help me. thank you in advance.

Wow! 50 cents each on Bl. I just bought 6 on ebay and paid $8 each. @@!!

What is the part number of the gear? 637 does not come up as a gear. I just bought 6 x1022 on ebay.

Oh I see know What you did.very clever of you. Right now Ive been working on building a rear sprocket. Your yellow rear sprocket 21t is no longer available as I checked bl. I'm trying to build up a sprocket using a small pulley and 3 1x7 half beams going across the pulley Making 6 teeth sticking out. Perhaps I'll search on building a proper sprocket. Well thank you very much.

Beatiful compact moc! Any way you can show or.tell us what you used to connect the track beams? Looks like cut pieces of tubing but cannot see. Thank you.

this is one of the best mocs i have ever seen! brilliant! would it be possible to send me additional photos of the base assembly where the xl batteries lay. i have started assembly of your masterpiece and cannot understand the base section. thank you.