Search the Community
Showing results for tags 'ford mustang'.
Found 4 results
Dodge Viper - 10265 c-model I made my first attempt to the Viper before building the Hummer. I wanted to use the white stripes offered by the 10265 set. I must admit that the Viper is one of the most iconic cars that use these painting. The problem is that it has an extremely slim silhouette, and the Mustang parts are much more suitable for the construction of an angular body. The final model is the result of 5 approaches. On the fourth, I had the model almost finished and all I had to do was construct a rear diffuser out of the scraps. It was not without a slight remodeling of the rear bumper, which left me with a few additional parts, which I knew would be very useful in the front. This way I demolished half of the car and it was a good decision. Thanks to this, the model has definitely gained stability. There are a few delicate details, but there is no risk that any of them falling off when you grab onto any part of the vehicle. The fairly low profile of the whole and the desire to reproduce the engine dummy in a decent way, eliminated the possibility of installing a torsion axle, which takes up so much space on this scale that it would have a negative impact on the appearance. Technical info Rebuild of the set 10265 Ford Mustang Model: Dodge Viper Parts: 984 - also used extra parts Height: 10,5 studs (8 bricks and 2 plates) Width: 16 studs (17.5 studs with mirrors) Lenght: 38 studs Functions: Opening doors and hood. Instruction: 298 steps on 189 pages. Flickr Brickshelf Instagram Rebrickable
Hogwartus posted a topic in LEGO Technic, Mindstorms, Model Team and Scale ModelingI'd like to share my most recent model - 1:10.5 replica of 1969 Ford Mustang Boss 429. Boss 429 was the high performance variant of first generation Mustang, equipped with a powerful 7.0 V8 engine. Only 1359 were made, and now there is one more :D Watch it in all its glory: Functions: RC drive - RWD with differential, 2x L motors RC transmission - 4 speeds, sequential, M motor Detailed V8 engine replica with fan connected directly to propulsion motors RC steering - with moving steering wheel, M motor Front suspension - double wishbone Rear suspension - floating axle Openable hood with lock controlled from the cabin Openable doors with locks Openable trunk Adjustable seats (sliding forward - backward and seatback angle adjustment) RC front lights Please watch the video to see this machine in action and for more details. I am quite happy with how I managed to include all the functions without compromising on proportions and interior in a relatively small model (46cm long). The biggest challenges were to fit piston engine over the suspension with the blue air intake under the hood without lifting it (as the result I had to make the hood hollow below the external air intake but still it was tight) and to fit interior over the gearbox. For that purpose I made the transmission very flat with gear shifting shaft actually crossing the drive shaft... (can be seen in action in the video - 2:30) I hope you liked this model.
Michael217 posted a topic in LEGO Technic, Mindstorms, Model Team and Scale ModelingWelcome to my garage LEGO!!! Hello! My name is Michael. I'm a Builder from Russia, I love muscle cars! All three cars produced in 2019) Instagram: https://www.instagram.com/lego_muscle_garage/ Join my group in VK: https://vk.com/legomusclegarage Dodge charger 1970 Description: -XL7.2 motor for drive, 375 Horsepower under the hood! -Servo motor for steering and steering wheel -Small power supply -Detailed interior All photos on the link: https://bricksafe.com/pages/Michael217/dodge-charger-1970 Chevrolet Camaro 1975 Description: -L 5.7 motor for drive, 300 horses!) -Servo motor for steering and steering wheel -Small power supply -Detailed interior All photos on the link: https://bricksafe.com/pages/Michael217/chevrolet-camaro-1975 Ford Mustang 2005 NFS Most Wanted 2005!!! Description: -L 5.4 motor for drive, 500 hell's horses!!! -Servo motor for steering and steering wheel -Small power supply -Detailed interior All photos on the link: https://bricksafe.com/pages/Michael217/ford-mustang-2005 Enjoy your viewing! Rate, comment! Thanks!)
Sheepo posted a topic in LEGO Technic, Mindstorms, Model Team and Scale ModelingThis is the car I showed in the Lego Fan Weekend two weeks ago. This creation is made in scale 1:8. The total size is: 75 studs of length, 29 wide and 21 of high (60x23x17 cm) The weight is 3.1 kgs, with around 3500 parts and 5 motors. It includes some remote controlled functions: - Steering (M motor) - Drive (2 L motors) - Sequential gearbox (PF Servo motor) - Disc brakes (M motor) The sequential gearbox is an improved version of my previous Caterham ones (3rd Gen V2), with 5+R and auto-clutch. The speeds ratio: R - 2.08:1 1 - 1.67:1 2 - 1.25:1 3 - 1:1 4 - 1:1.33 5 - 1:1.67 The max speed in 5th speed is 3 kph (~2 mph) It has a gear indicator in the interior, between the front seats. For make more easy the gearbox tests the car in has a rear support to keep the rear axle lifted The suspension is based in the real one: front McPherson axle and a rear 4-links live axle. The front axle also has advenced geometry: Camber angle(2º), caster angle(3.5º) and kingpin angle(7º) The steering has ackerman geometry and working steering wheel. The car also has working disc brakes in all wheels, they are very powerfull and includes functional brake pedal. The complete video COMPLETE INSTRUCTIONS WILL BE AVAILABLE COMING SOON!! As always for more info visit my website: sheepo.es