FernandoQ

Eurobricks Vassals
  • Content Count

    31
  • Joined

  • Last visited

Everything posted by FernandoQ

  1. FernandoQ

    [GBC] Akiyuki Ball Factory

    Thank you. The return of the ball is with the Tester a module with a snake longer than usual and the Pin-Ball elevator of Akiyuki. Also in this case I have used my Whirligig version with instructions from Matt Norman and an extended version of Maico's Skaerbaek.
  2. FernandoQ

    [GBC] Akiyuki Ball Factory

    My version of the Ball Factory (Akiyuki-Berthil) in its first public appearance https://youtu.be/tE-dekrEpLo
  3. FernandoQ

    [GBC] Akiyuki Ball Factory

    Hi Berthil, The Ball Factory is running with 21 buckets as it can be seen in the video. The problem with the Bucket Emptier was a little twitch due to a touch between the back wall and the emptier . I solved it by eliminating the yellow plate below. I'm still working on the Spiral lift improvement, as I still have doubts about the best solution.
  4. FernandoQ

    [GBC] Akiyuki Ball Factory

    My little circuit with the reproduction of Berthil's Akiyuki Ball Factory next to Maico's 4 bars and Fernando's Tester. A great job of Berthil that works wonders, only the spiral elevator gives me problems and something I have already improved. Thanks and congratulations Berthil. Fernando. https://youtu.be/3ydnf2G7BzA
  5. FernandoQ

    [GBC] The Akiyuki Project

    Ankou fact, there are losses in the Spin Robots balls, but they were the first test, now no falls.
  6. FernandoQ

    Rainbow Wave GBC

    Thanks Berthil, I put the rainbow-wave at the maximum speed of the 9v regulator. Then it works at a theoretical 70 balls per minute and works well. In half an hour only one stop to 55 real balls for 30 minutes, about 1650 balls. Very well. I also use a 9v regulator only for the rainbow-wave.
  7. FernandoQ

    Rainbow Wave GBC

    Now I have made the improved version of rainbow-wave and it works better, but I can not stand five hundred balls without getting stuck. The improvements introduced help smooth and constant operation.
  8. FernandoQ

    Rainbow Wave GBC

    I found the changes introduced very interesting. Thanks to Berthil and Courbet. I'm sure I'll do it again.
  9. FernandoQ

    [GBC] The Akiyuki Project

    Hello Doug72 The hands of the robot, rather the arms, and the neck. Three for each robot. That piece 24014 does not exist in any Technic set and I think we are missing almost all Technic fans
  10. FernandoQ

    [GBC] The Akiyuki Project

    My version of the Akiyuki Catch and Spin Robots with the Cup to Cup type 2 and the Hockey Sticks
  11. A great creation I have enjoyed watching the video many times and understanding all the solutions.
  12. FernandoQ

    [GBC] The Akiyuki Project

    My Tester module with an elevator equal to Pinball has the 2L red axles and I have never had to remove them. Greetings.
  13. FernandoQ

    [GBC] The Akiyuki Project

    My video of Akiyuki Hockey Stick Lift. It works wonderfully without any problems since the first test. Greetings.
  14. FernandoQ

    [GBC] The Akiyuki Project

    Akiyuki in addition to the video of the new railway system has placed on its website the instructions for the four modules of the basic layout. Only the instructions for the crossing of trains that we already had in Courbet's version are missing. I think it's the first time that Akiyuki gives us some GBC instructions.
  15. FernandoQ

    [GBC] Akiyuki project (EV3)(NXT)

    My version of the Sorter-Robot of Akiyuki with the instructions of Courbet, next to the Marble-Run and the Bucket Wheel Tower of Akiyuki and the Return and the Tester of Fernando. The Sorter-Robot uses the program of Courbet with modifications to count the balls and to be able to regulate the speed of the motor that moves the cylinder with the spiral. It also allows to stop the Sorter-Robot with the tactile push button leaving the different motors in their initial position emptying the ramps of the orange and white balls. Greetings. https://youtu.be/YLpi_ElQ_Y8
  16. 19: 10 3: 6 13: 4 15: 3 14: 2 5: 1
  17. FernandoQ

    [GBC] The Akiyuki Project

    Regarding the price of the cup, I was lucky and bought 14, almost two years ago, to make the Cup to Cup type1, for less than one euro each. It is clear that I am not a millionaire, but today they are very expensive like the balls.
  18. FernandoQ

    [GBC] The Akiyuki Project

    My version of Cup to Cup type2 of Akiyuki, made from the photos and video of its web. For the setting I think the best are the photos of the structure for the front and back. Put the axles, gears and cups in the same position and luck. Now with the instructions of Courbet the realization is easier, but for the final adjustment what commented in the previous line goes very well.
  19. FernandoQ

    [GBC] The Akiyuki Project

    Thanks Yoann, I did not know the part 20482.
  20. FernandoQ

    [GBC] The Akiyuki Project

    Incredibly fast. Of record. A question. What is the piece that raises the balls. In the video of Akiyuki are transparent, in yours they look orange and in Yoann's half and half?
  21. The 17 pods version is wonderful, and the music that accompanies it as well. What musical work is it?
  22. FernandoQ

    [MOC] Avtoros Shaman 8x8

    rm8 I really liked the video of your Avtoros Shaman. They look very good all the possibilities of the Madoca model. Congratulations.
  23. A beautiful model on a small scale. I like it more than many official 40th anniversary models. Greetings.
  24. FernandoQ

    [GBC] The Akiyuki Project

    Yes, it is right 9v system, but works much better with two motors: 5,000 balls processed and only one has fallen.
  25. FernandoQ

    [GBC] The Akiyuki Project

    My version of the "Invisible Lift" with two motors, adding a new one on the right side of the module, attached to the same axle as the original motor. Watch on youtube the video of Festbrick Japan 2015 at 4:39