SNIPE

So, we now know that the next 4x4 set will be the 42177 MercDees G500 4X4 Releasing August 1st for $250 and the set contains 2891 pieces. This thread is probably going to be quite long so I didnt append it to the '2024 technic set disgussion thread' Here are my speculations as to what it will have: A 4 speed gearbox using the new gearbox parts from set 42159 A fake V8 engine using the new parts from set 42170 Differentials from set 42143 (because its 4x4 :P) Maybe a center differental Working steering with HOG Working suspension Portal hubs or planetary hubs (the real car has portal gear axles) Maybe a winch. maybe not. -----Even better would be:----- 7 speed gearbox, 3 lockable differentials Adjustable ride height Flappy paddle gearbox Fake disc brakes I think the color will be black or neon yellow but it is unconfirmed so far. Go nuts! (And it looks like 2h 2024 will be good!)

So, this happned when taking apart the Icons mclaren MP4/4: So, i'll probably complain to lego that the ball sockets are a little too tight

agh I wanna build this pimped up chassis so bad and try to add adjustable ride height but im busy working on my 42177 MODs so ill have to wait... feel free to try and add it yourself though!

Hi, I'm working on some 42177 MOD's and was wondering if there was a part which fits in the antistud of minifig binoculars However it must also not replace the technic 1x1 bricks, or the clips I dont think its 1 plate as thats too big, but half a plate also seems wrong: Here is the .ldr file, I want this because the bars can rotate which makes the bars which are not in clips not be flush with the bricks/plates behind it... So, putting something behind the binocolars would solve this problem since the bars are very close together anyway. Regards, Snipe

oh my agod: think of the possibilities with this nut trick!!

The 1x1 technic bricks are in the way so I cant put the clips there. A bracket I cannot get to fit, I did try using the 1x1 bracket which is 2L high but the spacing for the binoculars is probably 1 brick apart not 1L

im not sure what part 29874 is but unfortunatley there must be a 1x4 tile on top so putting the hole over a stud wouldnt allow for the tile, and also there is a technic axle in front of the bricks on the side where the bars are and this would also not allow for a bracket or minifig vest such as 42446 I tried putting a flag square with 2 clips (2335) but despite being too awkward to get sitting clush with the bricks, it also was not long enough for both binoculars.

I'm gonna try to add adjustable ride height, it will require a lot of bracing but ive seen 3 other MOCs which use these shock absorbers and still have adjustable ride height.

I have 4 of these parts yes however they may pull out, it has the same clutch power as a standard axle You can get more clutch power by using 2 half bushes or 2 thin 1x2 beams You do know that the newer mould of the pinhole with pin 1L has less friction than the older mould right? You could use the small linear actuator as long as it doesn't have too much load on it so that it starts actuating rather than just spinning in place.

have you been using them outdoors? could be sand stuck inside the hubs

legendary work @jb70

I think the gearbox could have been massivley simplified using the old orange changeoocer catches, the old and new knob wheels, and the 24 toooth clutch gear and 12 tooth clutch gear.

New curved bricks available (5907, 5906) I made a ball out of them but didnt want to put the clutch cutouts together because the hole would be even bigger: LDR File And the internals:

Ah thx

Im amazed at LEGO sometimes, I bought this set and 42177 which came to like £389.98 and didn't get my free set, so I rang customer service and they said that the free set offer was on aug1 where as I made the order in like 27th of july. Fine, but at least give me some sort of free set... But I decided to return my unopned 42175 and buy it again + the white koenigsegg jesko which made the order high enough to qualify for the free set...

https://www.lego.com/en-gb/service/buildinginstructions/42177?marketfallbackfrom=en-fr still only book 2

Good point, I would prefer no slot because if you have say a blue pins it shows through and the models bodywork can look bad. I can't think of a pin that would have an impossible connection anyhow, stud pins would be a little harder to get out but this is not specific to this part, some pinholes are not thru-hole anyhow. like on motors or panels.

Still only book 2/2 on the lego instructions website.. Oh well ive finished book 1 so

Yes, comes in 42182 (x4)

I love it!

42174 Emirates Team New Zealand AC75 Yacht

New inverted tapered panels Looks like they are designed to mate with 4500 Technic Panel Curved 7 x 3 Inverted

I agree but lego are kinda pushing these newish low friction gears nowadays

Yeah, for example 1x3x7 panel has the 4 pinholes on the front then 3 pinholes on either side, so I personally think it can be moulded.

I would like a #1 connector but where both holes are pinholes.