Roadmonkeytj Posted October 26, 2018 Ok so I reach out once again. As I'm designing a Switcher for the switching layout. I won't have much time between the parts order and the show. I'm looking for a two wheel truck that is powered via an M motor... Could be remotely mounted. But it has to be great through switches as this lil guy will be all day through switches. Do any of you have a tried and tested good through switches powered design you would be willing to share? My plan is to have two pivoting trucks with two wheels each. Share this post Link to post Share on other sites
supertruper1988 Posted October 27, 2018 Any reason to not use the LEGO Train motor? Share this post Link to post Share on other sites
Roadmonkeytj Posted October 27, 2018 13 minutes ago, supertruper1988 said: Any reason to not use the LEGO Train motor? Other than looks.... No lol Share this post Link to post Share on other sites
supertruper1988 Posted October 28, 2018 How wide is your engine? anything that isnt that LEGO motor will need a side detail of some kind that will push you over the normal 6 studs and at that point, you may as well use the LEGO motor and build a custom side detail. Just my 2 cents anyways. Share this post Link to post Share on other sites
Roadmonkeytj Posted October 29, 2018 I'm keeping to the standard "legoesk" look even though all rolling stock, switcher and switch tower are moc's. 7w is the max I want to go ... I will try to grab a snapshot of what I have so far tomorrow Share this post Link to post Share on other sites
Roadmonkeytj Posted October 30, 2018 @supertruper1988 So here is the switcher as stands. The colors are to blend with the PF Batt box as I won't have time to wrap it. I just don't think the PF truck looks right lol Share this post Link to post Share on other sites
jtlan Posted October 30, 2018 Here's a simple design for an M-motor truck: (red pieces attach to the frame) This one isn't any shorter than the train motor, mind you, but you'll get a lower speed and much better pulling power at those low speeds. Share this post Link to post Share on other sites
Roadmonkeytj Posted October 30, 2018 45 minutes ago, jtlan said: This one isn't any shorter than the train motor, mind you, but you'll get a lower speed and much better pulling power at those low speeds. Thank you shorter isn't an issue ... Have you run this through switches with luck? I like the lower speed. Share this post Link to post Share on other sites
aawsum Posted October 31, 2018 This setup runs fine through switches. Torque is wonderful with this motor. I have this in a small shunter and as long as it is build strong it can tow a lot of wagons though any layout. I personally run standard lego layouts, so no wide curves or anything and it runs fine. Share this post Link to post Share on other sites
zephyr1934 Posted November 3, 2018 The one problem with that M-motor truck design is that the motor will torque the truck to one side. You will probably want to set the gearing so that the motor torques to the left when running forward (the right rail has a slight indent at the joints that these motors can climb when they torque to the right). The problem is more pronounced on 9v rail, but I think it is also there on PF track. If you operate where the impact of a derailment is small (e.g., on the floor) then probably not even worth worrying about. It is only when a table dive is at risk that you have to worry. Share this post Link to post Share on other sites
aawsum Posted November 3, 2018 Never heard this before. I have to say I do not drive a lot with pf, but that the motor is making the bogey tilt to one side is kind of interesting. Do you have this at all speeds or only at low speed. Share this post Link to post Share on other sites
Roadmonkeytj Posted November 4, 2018 19 hours ago, zephyr1934 said: The one problem with that M-motor truck design is that the motor will torque the truck to one side. You will probably want to set the gearing so that the motor torques to the left when running forward (the right rail has a slight indent at the joints that these motors can climb when they torque to the right). The problem is more pronounced on 9v rail, but I think it is also there on PF track. If you operate where the impact of a derailment is small (e.g., on the floor) then probably not even worth worrying about. It is only when a table dive is at risk that you have to worry. Here is the rough track plan... It has a L and R switch (PF/RC track) the front switch will be on the front edge of the table the decoupling will be done mechanically with levers 6 studs wide from the edge of the track (whole track sits 1 stud elevated to make room for axle- if this design works at the show I will "grade" the tracks with ballast for next year's show.) So would one side be preferable to the other in this case? 15 hours ago, aawsum said: Never heard this before. I have to say I do not drive a lot with pf, but that the motor is making the bogey tilt to one side is kind of interesting. Do you have this at all speeds or only at low speed. I had heard of them derailing through switches that's why I was asking for tried and true designs (I personally have never built a powered truck this way but everything has to be contained in a switcher not the consist so...) Share this post Link to post Share on other sites
zephyr1934 Posted November 9, 2018 On 11/3/2018 at 9:45 PM, Roadmonkeytj said: Here is the rough track plan... It has a L and R switch (PF/RC track) the front switch will be on the front edge of the table the decoupling will be done mechanically with levers 6 studs wide from the edge of the track (whole track sits 1 stud elevated to make room for axle- if this design works at the show I will "grade" the tracks with ballast for next year's show.) So would one side be preferable to the other in this case? I had heard of them derailing through switches that's why I was asking for tried and true designs (I personally have never built a powered truck this way but everything has to be contained in a switcher not the consist so...) Here's an old old post that I made about the issue... Share this post Link to post Share on other sites