Cjd223

(MOC) - Cavegod's UCS Sandcrawler

Recommended Posts

rough dimensions are 

37” or 94 cm “length"

18.3” or 46.5 cm “height"

10” or 25.4 cm “width"

Share this post


Link to post
Share on other sites

This Cavegod sandcrawler is just incredible! Cavegod.. please don't stop putting out the manual etc, I'm not quite ready to do it now but I would definitely buy the manual and all the bricks needed in the future! Can it all be bought as 1 kit?

What other creations have you made Cavegod? Did you make an AT-AT too?

Thanks!

Share this post


Link to post
Share on other sites
1 hour ago, Malthus101 said:

This Cavegod sandcrawler is just incredible! Cavegod.. please don't stop putting out the manual etc, I'm not quite ready to do it now but I would definitely buy the manual and all the bricks needed in the future! Can it all be bought as 1 kit?

What other creations have you made Cavegod? Did you make an AT-AT too?

Thanks!

Currently available are

At-At, Sandcrawler, Tie Defender, Zeta shuttle, 

Coming soon is the Rebel Transport  and Kylo Ren's command shuttle

Share this post


Link to post
Share on other sites

47234055792_1ec6097c6c_c.jpgUCS Sandcrawler Ready to crawl by Ragni Norgrimson, auf Flickr

Here is my beauty and how you could have seen it at the Lego Fanwelt 2018. 

32344410957_6aba3b0c93_c.jpgUCS Sandcrawler technical access terminal by Ragni Norgrimson, auf Flickr

This is the technical site I was talking about previously. 2 Servos are controlling the movement via switches. Above you can see a peak of the light panel I've installed in my interior.

Share this post


Link to post
Share on other sites
On 3/4/2019 at 12:03 PM, cavegod said:

Currently available are

At-At, Sandcrawler, Tie Defender, Zeta shuttle, 

Coming soon is the Rebel Transport  and Kylo Ren's command shuttle

Hey cavegod, you think you will offer the lambda shuttle some time?:))

Share this post


Link to post
Share on other sites

Thats not a Lambda thats an imperial landing craft

Share this post


Link to post
Share on other sites

The interior pics seem to show the the dark tread part no 3873 running the length but I can't find it listed in the parts list.  Can someone help out?

Share this post


Link to post
Share on other sites
On 7/22/2018 at 9:20 AM, bricksmarlin said:

I think you need 170 elements/parts for the conveyor belt!

30 for each of the 2 shorter ones and 55 for each of the the longer ones!

 

:wink:

Share this post


Link to post
Share on other sites

Bricksmarlin, thanks for the info.  Two questions: what do you mean by shorter and longer ones and what color(s)?  DBG?

Share this post


Link to post
Share on other sites
31 minutes ago, BadSisko said:

Bricksmarlin, thanks for the info.  Two questions: what do you mean by shorter and longer ones and what color(s)?  DBG?

I think you mean this section?
I hope the picture shows what I mean!
Color for 3873 is black!

full

Share this post


Link to post
Share on other sites

Hey guys, Wondering if someone can help me. I can't seem to figure out how these two joints connect together. I've been going over the instructions and it looks like I did everything right.

48315852736_7155cc0ded_c.jpg

Share this post


Link to post
Share on other sites
59 minutes ago, viptouge said:

Hey guys, Wondering if someone can help me. I can't seem to figure out how these two joints connect together. I've been going over the instructions and it looks like I did everything right.

just look at some pages before;)

Share this post


Link to post
Share on other sites
3 hours ago, muhkuh said:

just look at some pages before;)

I've been looking through the pages and can't seem to find it. By any chance you could post a pic of how this joint connects? Thanks  :)

Share this post


Link to post
Share on other sites
1 hour ago, bricksmarlin said:

This is the missing part!

AH! Thanks Marlin!   :sweet:

Share this post


Link to post
Share on other sites
On 9/7/2018 at 8:33 PM, bricksmarlin said:

Use plate 3794b above and underneath 57909 (brick with ball) to move the upper side walls backwards by a half stud.

gallery_8754_6681_90870.jpg

Then it should look like that.

 

My pleasure!
Check the pictures on side 11 to get the sidewalls mounted correctly!
Awesome collection by the way, and very nice pics!
The "monarch" is one of my next projects, can't wait to built it myself!

greetz
Steffen

 

Share this post


Link to post
Share on other sites
13 hours ago, bricksmarlin said:

My pleasure!
Check the pictures on side 11 to get the sidewalls mounted correctly!
Awesome collection by the way, and very nice pics!
The "monarch" is one of my next projects, can't wait to built it myself!

greetz
Steffen

 

Yes, thanks to your detailed photos, I fixed the alignment early on when I reached that point of the build. I didn't catch the link for the missing end ball and cup socket pieces until now when you pointed it out. Haha  Thanks again. The Monarch is for sure one on my favorite builds! I'm sure you'll enjoy it!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.