Murdoch17

Maintenance Of Way work train with 2-6-0+0-6-2 (Double Mogul) Garratt steam loco MOCs

Recommended Posts

Posted (edited)

"I've been working on the railroad, all the live-long day!"

This train consists of a 2-6-0+0-6-2 Double Mogul (Garratt-type) steam locomotive and five cars:
- a (working!) crane car
- depressed-center rail wagon
- a (working!) ballast hopper
- tool  / crew car
- caboose

This train is easily expandable using official models, such as the backhoe digger on a flatcar from set 60098, and / or the road-n-rail truck and it's depressed center wagon from set 3677.

37166647281_6d71aacdf6_z.jpg

The engine seen here pulls the Maintenance of Way train. This steam locomotive is a 2-6-0+0-6-2 Double Mogul (Garratt-type) steam engine. It  was originally designed by Anthony Sava but with fake pistons and with small-size friction bearing wheels. I added working pistons and Big Ben Bricks medium flanged and blind drivers wheels as see here at Ben's website. In my model, gear wheels are used as stand in for the custom wheels that are not in LDD. The engine is available for purchase at @SavaTheAggie Bricklink store.

37166647521_3946e37e11_z.jpg

The engine needs printed letter tiles with the railroad's initials "BRS" on the side of the boiler, while "3103" goes on the sides of the 1 x 4 bricks with side studs, placed on the four corners of the model near the pistons.

37166647571_6311d2f16f_z.jpg

Even with the added pistons, the engine easily can go around corners and switches.

37166648551_9d1fe28d79_z.jpg

This model was inspired by a coal hopper on an older website called LGauge .com. I tunrned the old finger hinges into new pin-orientated ones and colored the car yellow to match the MOW paint scheme.

36471946824_23736c7d47_z.jpg

The hopper's bottom door open and can dumpy 1 x 1 round plates / bricks onto the tracks for ballast.

37166648481_f913923866_z.jpg

The rail-carrying depressed-center wagon has brick-built arms to secure the cargo of railroad track in place.

36495831413_73ceaa655d_z.jpg

This stream crane model was heavily inspired by Whoward69's instructions for a set of crane and match truck train cars. I modified the original model seen here.  The crane car can move side to side or up and down with two sets of ropes to either raise / lower the hook or operate the boom. Several prints are missing from this car, including two of this four of these and two of this one.

36471947164_a0f8321588_z.jpg

Please NOTE: I don't have the exact measurements for the two strings as they wasn't listed in said instructions. However, I think two of this string here should be long enough.

37166646921_86a91892e5_z.jpg

This car is the tool car, carrying spikes, tie plates and track worker tools. (it really is empty) Two of this print go on the far side of this car.

36495831693_b6196447cc_z.jpg

The car features two opening side doors, allowing for quick access to the inside.

37166647161_4efa953ce1_z.jpg

The caboose should feature printed letter tiles with the railroad's initials "BRS" on the middle of the car below the windows.

Please know, the LDD will NOT be given out as the Garratt was not my design, and even though it is modified heavily by me to have pistons and four more wheels. However, Comments, Questions  and Complaints are always welcome!! 

Edited by Murdoch17

Share this post


Link to post
Share on other sites

Nice! Love the train as well as the color scheme. 5 studs wide for the train body and 6 studs wide for the cabin works great. Thumbs up.

Share this post


Link to post
Share on other sites

Very nice! The train looks very complete with the matching colour scheme on the last two wagons.

Regarding the overhanging crane, in many cases repairs are undertaken on two-track lines. This means that the crane (or more often two, working in tandem to increase lifting capacity and reduce chances of swinging loads) would be on one track, and could lift track panels off the wagons on the parallel track, then be shunted along to reach the place the panels are needed. Plasser-Theurer made some twin-jib cranes for exactly this purpose.

Share this post


Link to post
Share on other sites
18 hours ago, LegoMonorailFan said:

Nice! Love the train as well as the color scheme. 5 studs wide for the train body and 6 studs wide for the cabin works great. Thumbs up.

Thanks on the color scheme, but the original inspiration for the 5-wide body was Tony Sava's MRS-1 model seen here.

8 hours ago, ColletArrow said:

Very nice! The train looks very complete with the matching colour scheme on the last two wagons.

Regarding the overhanging crane, in many cases repairs are undertaken on two-track lines. This means that the crane (or more often two, working in tandem to increase lifting capacity and reduce chances of swinging loads) would be on one track, and could lift track panels off the wagons on the parallel track, then be shunted along to reach the place the panels are needed. Plasser-Theurer made some twin-jib cranes for exactly this purpose.

Thank you! I think I knew that about the cranes, but I just wanted to try to explain something that was pointed out to me by someone on the LEGO Train Fan Club group on Facebook. (It just didn't come out like I wanted it too.)

Share this post


Link to post
Share on other sites
Posted (edited)

Sorry for the slight BUMP:

35962693276_eb76e11496_z.jpg

The LDD file, text and pictures were just updated with a new steam locomotive, revised train cars, and printed parts have also been added to the train in many spots.

Enjoy!

Edited by Murdoch17

Share this post


Link to post
Share on other sites

35438825604_c2ed72f843_z.jpg

The rear of the crane car features the NEW control booth, and the first post has been updated as such with new pictures and crane-only LDD file!

Share this post


Link to post
Share on other sites

37166648331_9c0e861e0a_z.jpg

Main post updated with new Garratt-type locomotive and new ballast hopper car, and the entire first post has been retyped and restructured.

I hope you guys like it, it should be built somewhat soon, maybe in early November...

Edited by Murdoch17

Share this post


Link to post
Share on other sites

Don't you hate it when your this close to finishing you latest MOC and the realize you didn't have enough parts to finish -
 thus having to order more, delaying the entire project for at least a week or two?

37225077692_f5a8753aeb_z.jpg

I just need one (1) medium Big Ben Bricks flanged driving wheel to complete my latest steam loco, which I ordered this morning. I should have the rest of the breakdown train by early November / late October....

Share this post


Link to post
Share on other sites
7 hours ago, Murdoch17 said:

Don't you hate it when your this close to finishing you latest MOC and the realize you didn't have enough parts to finish -
 thus having to order more, delaying the entire project for at least a week or two?

Yep....that happened to me recently.......Nice train by the way!

Share this post


Link to post
Share on other sites
On 9/23/2017 at 5:02 PM, Hart New Bob said:

Yep....that happened to me recently.......Nice train by the way!

Thank you for the compliment!

37440000001_d87d95fce3_z.jpg

Since the last update on this steam loco, I realized I needed more weight over the drivers while building the model in real bricks. I have ordered a couple weight bricks and new boiler parts to hide them in in order for the wheels to grip the rails sufficiently for the pistons to work.

The parts should be here soon, and the real world reveal of the engine will happen shortly thereafter. (The rest of the train will have to wait until Christmas to be built, sadly)

Share this post


Link to post
Share on other sites
Posted (edited)
Just now, Goldenmasamune said:

I really want to see more of that steam engine you posted in an earlier post .

35833466582_7ba6f9a3c4_z.jpg

This one @Goldenmasamune? The LDD file for it is available here along with an earlier version of the breakdown train.

35962692746_354d34c352_z.jpg

I sadly don't have any more photos of it besides the rear view.

Edited by Murdoch17

Share this post


Link to post
Share on other sites
1 hour ago, Murdoch17 said:

 

This one @Goldenmasamune? The LDD file for it is available here along with an earlier version of the breakdown train.

 

I sadly don't have any more photos of it besides the rear view.

Yes, that's it! I really love the design!

Share this post


Link to post
Share on other sites
On 10/3/2017 at 12:42 PM, Murdoch17 said:

 

This one @Goldenmasamune? The LDD file for it is available here along with an earlier version of the breakdown train.

 

I sadly don't have any more photos of it besides the rear view.

 

Would you be terribly offended if I built this? 

Share this post


Link to post
Share on other sites
7 hours ago, Goldenmasamune said:

 

Would you be terribly offended if I built this? 

No, I would be excited! I always upload the LDD files so people can built things on their own, either by tinkering with my build to make it special or just making a carbon copy of what I did. Please post pictures when it's done @Goldenmasamune!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.