[TC11] Technic Contest Battle Bots - Entry Topic

[heyitsdisty]

25. Name: THUMPER

Category: Cat B (IR receiver)

Dimensions: 29 x 24 x 18

Signature move: Disc spinner uppercut

Functions: Two M drive motors and one XL weapon motor, all operated with IR remote control and powered with a AAA battery box. Rubber band suspension on front wedges, keeping them flat to the ground and reducing ground clearance.

Topic:

 

 

 

[teos]

26. Cat. B: PF IR

Name: La Grange 3001 

Signature move: Tongue Spinner

Size: 39l x 20w x 12h

Weight: 1663g

Motors: 2L, 2M, 2 receivers, 1 battery box

The idea was to make a marbled "Grangemouth" 3001 brick.  The controller requires two hands to operate, though I only had one.  The other was holding my phone to video.  

20170416_205655 by topazard, on Flickr

20170416_205706 by topazard, on Flickr

 

Link to work in progress post:

 

[pangniadek]

27. Cat: A

Name: Harvester of Sorrow

Signature move:

                          Weapon: Super Ultra High Speed Mega Blast Titanium Spinning Drum
                          Defens: Steel Rope and Poison Hook

Size: 32 x 33 x 8.5 (studs)

I admire your robots from the very beginning and I want to congratulate you on each of your ideas and solutions.
A little fear with my 7 hours building:

HoS is a two-sided robot that shreds everything that's on the way!
The spinning drum absorbs the blocks at full speed, and the rear rope blocks the opponent's movements by twisting into his wheels and mechanisms (breaks loose).

This is not a big robot, but it's fast (2x M Motor) and nimble.

 

Forum link: 

 

And remember .. Respect is everything;)

[Wilbero79]

28. Deathclaw

Cat B: PF IR receiver

Spins of Death (signature move)

It has two M motors with "sticks" on them that spin rather fast, it is also powered by two L motors which control the craft, as well as making it spin with it's 6 full battery boxes

 

 

[Erik Leppen]

29. Entry name:
Wimbledoom

 

Category:
Cat B: PF IR

 

Signature move name:
Dual horizontal hammers

 

Short summary of the functions:

• Control: 1 battery box, 2 receivers, 2 remotes, 4 M motors
• Drive: M motor for left wheel; M motor for right wheel
• Weapon: M motor for releasing the hammers; M motor for returning the hammers

 

Images:

 

Video:

 

Discussion topic:
Wimbledoom - Discussion topic

 

[JTS]

30. Name: Mr Cuddles
Category: B - PF IR

Signature Move: Grab 'n' Stab
Weapons: Large claws grip the opponent so they can't escape, then a powerful axe smashes them from above
Power: 2x Battery Boxes, 2x IR Receivers, 2x XL motors for drive, 1x L motor for axe, 1x M motor + 2x LAs for claws
Dimensions: 45L x 40W x 18H studs (in idle mode)

• Claws extend to 60 studs wide to ensure even the largest opponents cannot escape
• Thick all-round armour plating protects all essential functions and components
• Ride height is less than 0.5 studs and the centre of gravity is very low down to protect Mr Cuddles from flipper-bots
• Quick and agile, despite weighing 1.85 kg
• Battery boxes are easily accessible for quickly replacing flat batteries ( see video)

Other features:

• Intimidating name 
• 12 sharp horns (possibly venomous!)

The link to the discussion topic is here, and more images including some WIP can be found here.

I hope you enjoy!

[AVCampos]

31. Here is my entry, Devil's Tongue.

Category: Cat B (PF IR)

Signature move: Devil's Spoon

Functions: it has four-wheel drive powered by two XL motors, and can move upside down. The flipper, "Devil's Spoon", is spring loaded. It has a mechanism that uses a single motor to pull the flipper down and release it, via differential and clutch. The rounded sides, as well as the capability of upside down drive, prevent it from getting stranded by the adversary.

Here are some images:

Here is a video of it in action:

 

The discussion topic can be found here:

 

[The Vooduist]

32. My first entry Claw-Crawler

CAT A: sbrick plus (not using sensors)

Signature move- Quick claw (propelled by buggy motor for quick grabbing or tearing apart bots)

Size: L45 studs W29 studs (drill and spoiler were taken off for the final model due to length)

Propulsion: 2xl motors for driving/steering and 1 buggy motor for the claw

Description: This is my Claw-Crawler, a slow but very powerful battle bot tank built to grab its enemies. Then, if in a related battleground area (just like on the real deal) were they have the hammer, drills grinders, and etc it would destroy them by using the weapons on the battleground by driving them into the death sentence traps! Also due to its massive torque it can crawler over other bots and squish them. This was designed for powerful side or top impacts. If you design your battle bot correctly and can take 3-6 whacks were the battery box is and detach it, it mite do something but the crawler will still run just not as fast (it is unlikely that it would knockout the robot).

The drill and spoiler are NOT in the final bot.

Inside

size to 45 studs (Barely)

Good luck everybody!

Discussion: