Umbra-Manis

[Challenge 5][Cat A] The Tourniquet

Recommended Posts

The Tourniquet

The Engineering department at MANTIS has been hard at work producing The Tourniquet, a highly advanced mech, for the inaugural Andromeda Olympics. Let's take a look at their creation!

800x600.jpg

Torniquet1.png

Tourniquet2.png

And Here's the all existing parts version, which adds some grey spots.

Tourniquet4.png

Size Proof:

The legs and arms are both on a rotation only joint with no outward movement at the hip and shoulder respectively. The knees and elbows are the only places where they can move out to the side.

800x363.jpg


I think this is the best mech I've built so far, so C&C welcome! And check out the 360 view on Mecabricks!

Edited by Umbra-Manis

Share this post


Link to post
Share on other sites

This is really nice! However:

  • Q: Can I post a digital MOC?
    A: Digital MOCs are allowed, but specific challenge could says otherwise. You'll have to check rules of each challenges. in any case, digital MOCs should be buildable with real bricks. No floating pieces, no unavailable combination of parts and colors.

At the very least the 1x1 tooth tiles aren't available in lime. I don't think the tubes are available in trans neon/bright green either :hmpf_bad:

Edited by Big Sal

Share this post


Link to post
Share on other sites

If it was an actual competition with this size restricting rule only I'd imagine this design would be the best.

It reminds me of the Lil' Longlegs but a lot beefier and with a lower center of mass. It's like a sumo wrestler compared to most boxer types. Other then the small ones that focus on ripping apart there opponents I think the only one who could take down this one is the Pombe mech who could headbutt it to the ground.

Share this post


Link to post
Share on other sites

This is really nice! However:

  • Q: Can I post a digital MOC?
    A: Digital MOCs are allowed, but specific challenge could says otherwise. You'll have to check rules of each challenges. in any case, digital MOCs should be buildable with real bricks. No floating pieces, no unavailable combination of parts and colors.

At the very least the 1x1 tooth tiles aren't available in lime. I don't think the tubes are available in trans neon/bright green either :hmpf_bad:

Thanks for the Reminder Big Sal! I've switched the hoses to black, and replaced the tooth plates with standard round tiles. I'll upload the fixed main image once it's done. :classic:

This one is really great

I like the constracting effect on the black parts... looks matify

Thanks!

If it was an actual competition with this size restricting rule only I'd imagine this design would be the best.

It reminds me of the Lil' Longlegs but a lot beefier and with a lower center of mass. It's like a sumo wrestler compared to most boxer types. Other then the small ones that focus on ripping apart there opponents I think the only one who could take down this one is the Pombe mech who could headbutt it to the ground.

Thanks Epsilon! I Haven't had a chance to look at other builds in a while, so thanks for linking to some great ones!

Share this post


Link to post
Share on other sites

Thanks for the Reminder Big Sal! I've switched the hoses to black, and replaced the tooth plates with standard round tiles. I'll upload the fixed main image once it's done. :classic:

Not like it's the judges job to find all the wring parts but the Axle Connector for the hands and mixel joint holder in the knees doesn't exist in black either. (but in DBG)

Share this post


Link to post
Share on other sites

The judges awarded you 3 points (points were subtracted for rules violation).

What rule did I violate? I posted the updated version with all existing parts before the deadline.

Share this post


Link to post
Share on other sites

What rule did I violate? I posted the updated version with all existing parts before the deadline.

You still have many parts that do not exist in those colors

Here are some I found

The hammer https://www.bricklin...e?id=109413#T=C

The shield http://www.bricklink...age?P=91884#T=C

Round tile with stud https://www.bricklin...age?P=18674#T=C

Round tile with hole https://www.bricklin...age?P=15535#T=C

Share this post


Link to post
Share on other sites

You still have many parts that do not exist in those colors

Here are some I found

The hammer https://www.bricklin...e?id=109413#T=C

The shield http://www.bricklink...age?P=91884#T=C

Round tile with stud https://www.bricklin...age?P=18674#T=C

Round tile with hole https://www.bricklin...age?P=15535#T=C

I uploaded the file to rebrickable for easy checking, and I corrected all the errors. The hammer is light bluish gray, but isn't visible. The shield is pearl dark gray, and it's reflecting the black leg. 15535 comes in black in two summer sets, and 18674 isn't used in the MOC. Here's the parts list from the final render.

Share this post


Link to post
Share on other sites

Very unique build. The design is interesting. Very heavy. It looks like it'd do very well in a real mech contest like this... since I don't think it'd be too easy to knock this guy out! :grin:

~Insectoid Aristocrat

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.