zul alpha 3

Remote Switch Tracks

Recommended Posts

traintech1.jpg

Dear Eurobrick forum

I am fairly new to the lego train world. I have a rail track with several swith tracks (incl double crossover).

I am now looking for possible solution to manage / control them remotly through 9v motors. I've seen some solutions on the net however they were all very 'large' (six to eight studs long/wide). -> http://www.freelug.org/article.php3?id_article=186

are there any lighter versions / ideas / suggestion around?

thanks for any comments

Share this post


Link to post
Share on other sites
9V micromotor would probably be the best one if you're looking for a discreet solution.

This would require some track modification, otherwise it takes too much force

to move the lever. I do think track modification is the best way to go though. You can

find it on the web how to do it. If you have two remote controlled switches near one

another, you could save on wiring by powering them with batteries and using

the IR remote controlled power functions.

Share this post


Link to post
Share on other sites
Dear Eurobrick forum

I am fairly new to the lego train world. I have a rail track with several switch tracks (incl double crossover).

I am now looking for possible solution to manage / control them remotely through 9v motors. I've seen some solutions on the net however they were all very 'large' (six to eight studs long/wide). -> http://www.freelug.org/article.php3?id_article=186

are there any lighter versions / ideas / suggestion around?

thanks for any comments

This is still a 'large' solution, as it requires a 4x6 stud space off the end of the switch arm but

http://www.flickr.com/photos/whoward69/373...57621512518259/

does have the advantage that it uses current parts, esp the new pf M motor.

This is probably as elegant a lego solution as you'll find, smaller solutions will require modification of the points or use of non lego elements.

Hope this helps.

Share this post


Link to post
Share on other sites
This is still a 'large' solution, as it requires a 4x6 stud space off the end of the switch arm but

http://www.flickr.com/photos/whoward69/373...57621512518259/

does have the advantage that it uses current parts, esp the new pf M motor.

This is probably as elegant a lego solution as you'll find, smaller solutions will require modification of the points or use of non lego elements.

Hope this helps.

thank you very much for this hint - works perfectly. also tried with modification which goes better for the older V9 motors ...

thanks again ... any other hints / suggestions around ...

Share this post


Link to post
Share on other sites
thank you very much for this hint - works perfectly. also tried with modification which goes better for the older V9 motors ...

Don't just say it worked, take pictures and show them! :classic:

especially of any modifications that improve things,

That way everyone can share the work you've done.

What size set up are you working on, what's your rolling stock like?

It's great we were able to help, but say it with pictures, they say a 1000 words!

Share this post


Link to post
Share on other sites
Don't just say it worked, take pictures and show them! :classic:

Thanks for the reference.

Pictures of the motors in-situ on my 1/6th of the GWLTC layout at STEAM last year

4064889795_5a686405d0_m.jpg

4064888937_8cf494ea03_m.jpg

William

Share this post


Link to post
Share on other sites
Dear Eurobrick forum

I am fairly new to the lego train world. I have a rail track with several swith tracks (incl double crossover).

I am now looking for possible solution to manage / control them remotly through 9v motors. I've seen some solutions on the net however they were all very 'large' (six to eight studs long/wide). -> http://www.freelug.org/article.php3?id_article=186

are there any lighter versions / ideas / suggestion around?

thanks for any comments

Have you considered pneumatics?

Mechanisms

Scenic Modules and connections

Mark

Share this post


Link to post
Share on other sites

Hi there,

If you don't mind a non lego solution you could try something like i have made and use to motorize my points.

points_motor.jpg

Theres a few more pictures in that folder of the motor etc.

Advantages: One of the smallest footprints you will find for a points motor. Motors can be acquired free from most old CDROM drives. Can be disguised easily as a track-side cabinet.

Disadvantages: Not 100% Lego components. You do have to modify the point to reduce friction as these motors have little torque.

I cannot take credit for using this type of motor as i had got the idea from someone else. I managed to find the original article at http://www.freelug.org/article.php3?id_article=507 by Xavier Viallefont.

I pulse the motor for about a tenth of a second at 12 volts and it works just fine, and can run on as low as 5 volts if required.

Mike

Edited by skaako

Share this post


Link to post
Share on other sites

skaako,

I really like your design of motorised switch point!

Can you give more details as to how you fit the motor inside that lego box?

It looks like the motor is inside a 4x2 brick? Did you cavitate it to get it in there?

Is motor just glued straight to lever with a 1mm hole??

Thanks!

sPy

spy1101001@hotmail.com

Share this post


Link to post
Share on other sites

spy1101001 I have sent you the plans on how to make one, If anyone else would like them please send me your email.

These are plans to make the switch motor with a small RC motor.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.